PrintVerdict

3d printer filament at £12 a kilo: what PLA, PLA+ and PETG cost in the UK

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

Spend five minutes on Amazon UK and the pattern is obvious. Black PLA+ is £12 a kilo. White and grey, also £12. Bright red, green flash and tropical turquoise, £13. Vibrant yellow, £14. PETG in black, £12. Ordinary PLA in yellow, blue, silver or brown, £13. Resin sits apart: £13 to £15 for a kilo of standard or water-washable, £28 for a high-speed bottle.

That price ladder is not random. It is the most useful thing to understand before you buy your third spool, and almost nobody explains it.

We have not tested any of these filaments. The prices and ratings are from the current UK listings; the material behaviour described below is standard published extrusion data, not something we measured.

Why black and white are the cheapest

Natural PLA is roughly the colour of milk. Getting to black or white takes pigment, and both are cheap, high-opacity pigments that hide layer lines and print consistently. Colours are harder: each shade needs its own masterbatch, each batch has to match the last, and small runs cost more. Special effects — silk, matte, glitter, marble — add a third cost layer because the additive changes how the plastic flows.

So the £12 shelf is the boring shelf. Black PLA+ at £12 is the cheapest sensible thing you can put in a printer, and for most functional parts it is also the right thing: black hides layer artefacts better than any other colour, and PLA+ is tougher than plain PLA without needing different temperatures.

PLA versus PLA+ versus PETG

Plain PLA prints at 190–220 °C with a bed around 45–60 °C. It is stiff, dimensionally accurate, and the easiest material to get a good first layer with. It is also brittle and it softens at around 55–60 °C, which means a PLA part left in a car in July will sag.

PLA+ is PLA with an impact modifier. Same temperature range, noticeably less brittle, slightly more stringing. For brackets, boxes, tool holders, and anything that will get dropped, it is the better £12. Anker's own listing prices coloured PLA at £13 — a pound for the colour, which is fair.

PETG prints hotter: 230–250 °C, bed 70–80 °C. It is more flexible, more heat-resistant, and much more prone to stringing and to bonding so well to a smooth bed that it takes a chunk of the surface with it. PETG at £12 is the cheapest way to make something that lives outdoors or in a hot car. It is also the material most likely to ruin your first three prints.

The kilo maths

A kilo is 1,000 grams. A phone stand is 30–50 grams. A 200 mm planter is 150–250 grams. A full 256 mm cube of solid plastic would be several kilos, which is why nobody prints solid.

Practically: one £12 spool covers a dozen small functional prints or three or four medium ones. That is why the price difference between £12 and £14 matters less than people think — a £2 spread on a spool is 20 pence per small part. What actually costs money is failed prints, and failed prints come from wet filament and bad first layers, not from cheap plastic.

Drying matters more than brand

PLA absorbs moisture slowly, PETG faster, and wet filament shows up as popping noises at the nozzle, stringing, and weak layer adhesion. A £12 spool that has sat open in a garage for a year prints worse than a £14 spool opened last week.

Two cheap habits fix this. Store open spools in a sealed bag with a desiccant sachet, and dry a suspect spool at 45–50 °C for four to six hours before blaming the settings. A dedicated dryer box costs more than four spools of filament, so start with an oven on its lowest setting and a thermometer — and accept that a domestic oven that overshoots will turn a PLA spool into a fused brick.

Resin is a different budget

Standard 405 nm resin at £13–15 a kilo looks comparable to filament. It is not, because resin printing consumes gloves, isopropyl alcohol, and paper towels, and because a failed print wastes a vat rather than a few grams. Water-washable resin at £15 removes the alcohol cost at the price of slightly weaker parts.

If you are buying resin for the first time, buy one kilo of standard grey. Grey shows detail better than white or black, and standard resin is more forgiving than the fast or tough variants.

One more thing worth knowing before the first order: filament diameter is specified as 1.75 mm and the tolerance is what separates a good spool from a bad one. A spool that varies by a tenth of a millimetre will print fine on one machine and jam on another. That is the argument for paying £13 instead of £9 on a marketplace listing with no brand name — not colour, not packaging, just the odds that the diameter is what it says on the box.

What I would buy first

Two spools, not twelve. One black PLA+ for functional parts, one colour you actually like for things people will see. That is £24 and it covers the first month of ownership. Buy PETG when you have a specific part that needs to survive heat or weather, and buy a second colour when you are bored rather than when you are planning.

The £12 to £14 spread is a rounding error next to the cost of the printer. Buy the boring spool, store it dry, and spend the saved money on a decent pair of calipers — they will improve your prints more than any filament upgrade.