Anycubic Kobra S1 ACE 2 Pro Combo at £485: the best 3d printer for beginners who want colour without the Bambu tax
£485 for an enclosed CoreXY printer, a 320 °C hotend, and a four-spool filament dryer that feeds the machine while it prints. That is the entire pitch, and at this price it is a hard one to beat. The Kobra S1 ACE 2 Pro Combo is listed at £485 with 4.1 stars from 858 ratings; a second listing carries the same hardware at the same money with 789 ratings, so check both before ordering.
TechRadar's Alastair Jennings reviewed the S1 and did not hedge: "When it comes to absolute precision, the Anycubic S1 is one of the best 3D printers out there." He put the print finish down partly to the ACE 2 Pro's built-in dryer — filament that goes in dry produces a visibly better surface than filament that has been sitting in a humid room.
The specification that matters
250 × 250 × 250 mm build volume, enclosed chamber, 600 mm/s maximum speed, 320 °C quick-release hotend, LeviQ 3.0 automatic levelling and resonance compensation. Materials run from PLA and PETG through ABS and ASA to TPU, which is exactly what the enclosure is for: ABS and ASA warp without still, warm air around them.
The ACE 2 Pro does two jobs. It switches between four spools automatically and it dries filament at up to 65 °C while the printer is working — you do not have to finish a drying cycle before starting a print. It reads compatible filament, estimates what is left on a spool and refills automatically. Add more ACE units and the system expands to 16 colours. The other £485 listing, 4.2 stars from 789 ratings, describes the same bundle as a "quiet CoreXY enclosed FDM" machine — same printer, different copy.
That last number is doing a lot of marketing work. Sixteen colours is not what comes in the box. You get four. The other twelve require three more ACE 2 Pro units, and each of those lists around $290. Anyone quoting "up to 16 colours" as a feature of a £485 purchase is describing a £1,200 setup.
Where the money actually disappears
Purge. Every colour change cuts the old filament, purges the nozzle and reloads. VoxelMatters measured the cost on this machine family and the number is brutal: a 10.9 g Benchy generated 183 g of purge waste. Seventeen times the weight of the model, thrown away. Each swap takes roughly two minutes, so a one-hour single-colour print can turn into nine hours or more in four colours.
Worse, the stock Anycubic Slicer Next does not show you the real purge volume before you commit, so the first time you learn what a multicolour print costs is when you are emptying the waste bin. This is not an Anycubic-only problem — every filament-switching system on the market has it — but it is the single reason people buy a multicolour printer and then print everything in one colour.
The software is the weak joint
Tom's Hardware's Denise Bertacchi reviewed the Kobra S1 and titled her verdict "Good printer, bad slicer." A good Core XY machine, spoiled by flawed software. That was 2025, and the firmware has moved since — Anycubic's V2.6.8.8 release notes explicitly fix frequent PETG nozzle clogs, and V2.6.9.2 optimised purge length — but the slicer complaint is the one that recurs in owner threads.
The clog story is worth knowing before you buy, because it is fixable and it is not obvious. Wet or old PETG snaps inside the hotend during retraction; the fix is drying filament, lowering retraction distance, and updating firmware first. The ACE feed system has its own error codes — 11518 for a detected clog, 11511 for a feed timeout, 11519 for a tangled spool — and the official first step, restarting the ACE so the feed gear resets, clears most of them.
What owners say after the honeymoon
A detailed write-up in r/AnycubicKobraS1 from a hobbyist who came from an Ender 3 Pro is more useful than any launch review. His summary: single-colour prints came out as expected, multicolour through the original ACE Pro was a different story, and he had bed-levelling trouble until a $20 GECO cool plate fixed adhesion permanently.
He then moved to a Bambu Lab P1S and delivered the most balanced verdict available: print quality is better on the Bambu, "the Kobra S1 was better, when it worked." He missed specifics — the Anycubic app shows the current layer number, lets you change nozzle, bed and chamber temperatures remotely, reports filament used and total print hours, and pushes firmware updates. The Bambu app, on the more expensive machine, shows progress and an estimate. He also noted his AMS cannot dry while printing, which the ACE 2 Pro can.
Read that as a statement about maturity, not hardware. Bambu's ecosystem is more polished; Anycubic's is more capable per pound and rougher at the edges.
Who should buy this, and who should not
Buy it if you want an enclosed printer for ABS or ASA, you plan to print in two to four colours regularly rather than occasionally, and you are willing to spend an evening learning a slicer that is not as friendly as Bambu Studio. The enclosure plus dryer combination at £485 is genuinely good value, and it is the reason this machine keeps appearing in "best" lists despite the software complaints.
Do not buy it if your output is single-colour PLA brackets and boxes. You would be paying for a filament changer and a dryer you never switch on, and a plain Kobra or an A1 mini does the job for less. Do not buy it for 16 colours either, unless you have already priced the three extra ACE units and the shelf space they need.