Anycubic Kobra X at £279.99: six UK listings, one name — which is actually the best 3d printer for beginners
£279.99, 4.3 stars, 272 ratings. But type "Anycubic Kobra X" into Amazon UK and you get six different listings between £279.99 and £559, and the cheapest one is not the one with the most reviews. That gap — £280 for the beginner version, £310 for the 600 mm/s version, £450 and £559 for the combos — is the real buying decision here, and it is much more consequential than the colour count on the box.
The variation matters because the Kobra X is being sold as a beginner machine and as a multicolour machine at the same time. The £279.99 "for Kids and Beginners" listing carries 4.3 stars from 272 ratings. The Multicolor version with ACE second-generation technology is £280 at 4.1 stars from 860 ratings — nearly the same price, three times the review base, and a slightly lower average.
What third-party testers concluded
TechRadar reviewed the Kobra X directly and headlined its verdict "a 4-color 3D printer that's surprisingly good", describing it as beginner-friendly. That is a positive result from an outlet that, by its own count, has reviewed more than fifty of the best 3D printers of 2026 — it has plenty of comparison points.
Tom's Hardware asked a blunter question in its review title: "Another Bambu Lab clone, or something better?" The framing tells you where the market sits. The Kobra X is competing in a category defined by Bambu Lab's multicolour workflow, and the honest reason it keeps coming up is price. An enclosed, automatic multicolour machine from the established players costs considerably more than £280.
What none of the coverage claims is that this is a set-and-forget appliance. Multicolour printing at this price involves filament changing, waste material, and a slicer profile you will need to learn. Anyone buying it expecting a Bambu Lab experience at a third of the price should recalibrate.
Which of the six to buy
Start with what you want to print. If you want single-colour functional parts and you want to spend as little as possible, the £279.99 base machine is the entry point. If you want four colours out of the box, the £280 Multicolor variant is the better-reviewed option at the same money — 860 ratings against 272 is a materially better sample, even allowing for the slightly lower 4.1 average.
If speed is the priority, the 600 mm/s version at £310 carries 4.2 stars from 1,295 ratings, which is the largest review base in the entire Kobra X range on the UK site. Thirty pounds for the highest-confidence listing is arguably the best value in this family.
The combos are a different purchase. The native seven-colour Combo with support for up to nineteen colours is £559 at 4.1 stars from 858 ratings, and a second Combo listing sits at £450 at 4.3 stars from 268. Seven colours at £450 is nearly twice the base price. Decide whether you will genuinely print multi-material models before paying for that capability — most people do not, and the difference buys a lot of filament instead.
The beginner question, answered honestly
Is it a beginner printer? For assembly and first prints, yes — the whole category has moved toward autocalibration and guided setup, and TechRadar's reviewer specifically framed the machine as beginner-friendly. For multicolour work, no. Every multicolour system at this price demands that you understand purge volumes, filament profiles and print orientation, because colour changes are where the waste and the failed prints come from.
One thing to note about the feedback we could and could not find. Across this research round we did not surface a body of Kobra X-specific owner complaints on Reddit, which is unusual for a machine with thousands of UK ratings. That absence is not evidence of reliability — it is simply an absence, and it means the Amazon rating averages above are your main signal.
The practical route for a first printer: buy the listing with the largest review base that matches your actual need. On the UK site today that is the 600 mm/s four-colour version at £310, not the cheapest one. If you want to see the current mid-range listing as well, compare its price against the £310 before deciding — these listings move by £20 to £50 without notice.
What the price jump actually buys
Lay the six UK listings side by side and the ladder is clear. £279.99 for the four-colour beginner machine at 4.3 stars from 272 ratings. £280 for the Multicolor with ACE second-generation technology at 4.1 stars from 860 ratings. £310 for the 600 mm/s four-colour version at 4.2 stars from 1,295 ratings. £330 for a faster Multicolor at 4.2 stars from 789 ratings. £450 for the seven-colour Combo at 4.3 stars from 268 ratings. £559 for the seven-colour Combo supporting up to nineteen colours, at 4.1 stars from 858 ratings.
Read that as three tiers rather than six products. Under £300 you are buying a single-toolhead machine that changes colour by swapping filament. Around £310 you are buying speed. At £450 and above you are buying a filament-changing system — the ACE — and that is a structurally different machine, not a faster version of the cheap one.
The £310 listing is the one to look at hardest. It has the largest review base in the family, 1,295 ratings, and a 4.2 average, and it costs thirty pounds more than the entry model. For a first printer, that is the listing with the most evidence behind it.
The costs nobody puts on the box
Budget for filament and for waste. A four-colour print purges material every time the extruder changes colour, and on machines at this price the purge volumes are set by you in the slicer. Get that wrong and a multi-colour model can consume several times the filament of a single-colour print of the same object. The seven-colour combos make the effect larger, not smaller.
Budget for time as well. Speed ratings such as 600 mm/s are headline numbers for straight-line infill; real models with lots of small features and colour changes run far slower. The honest expectation for a beginner is that the first week is setup and calibration, the second week is learning the slicer, and the machine only becomes a tool once both are done.
If you already own a printer and want multicolour, the £450 seven-colour Combo is the sensible target — it has a 4.3 average, the best in the family, from 268 ratings. If this is genuinely your first machine, buy the £310 speed version, single-colour for a while, and add multicolour later when you know which materials you actually print.
We have not tested this printer. Price, star rating and rating count are read from the retail listings on the day of writing. Performance commentary is attributed to TechRadar, Tom's Hardware and Anycubic's own published specifications.