Anycubic Photon Mono 4 Review: a £190 resin 3D printer in the same chassis as the Ultra
£190. That is what a 6.04 × 3.42 × 6.49 inch resin printer costs in the UK right now, and it is less than a mid-range FDM machine. The Photon Mono 4 sits at the bottom of Anycubic's current resin ladder, below the Mono 4 Ultra at £250, and it uses the same build envelope: 153.4 × 87 × 165 mm, which is small enough to fit on a shelf and large enough for a 1:12 figure with a base.
We have not printed on this machine. What follows is what the listings state, what independent reviewers have published about the Mono 4 family, and the workflow costs that the product page does not mention.
The two £190 listings, and why you should care
There are two Photon Mono 4 listings in the UK catalogue at the same £190. One is titled simply "Photon Mono 4 Resin printer" and carries 4.1 stars from 102 ratings. The other is titled "Photon Mono 4 10K Resin 3D Printer" with the same three build dimensions and carries 4.5 from 43 ratings.
Same price, same size, different name, different average. That is worth thirty seconds of your attention before you click buy, because on a resin printer the panel is the expensive component: a 10K mono LCD and a 4K one look identical in a product photo and behave very differently on a 28 mm miniature.
The base listing: Photon Mono 4 at £190. The 10K-named listing at the same price: Photon Mono 4 10K at £190.
What the Ultra tells you about the base model
The most detailed public teardown of this chassis is about the Mono 4 Ultra, not the plain Mono 4, and that distinction matters. Printer-Hub's fault database lists the Ultra's hardware as a 7-inch 10K mono LCD at 9024 × 5120 pixels (17 µm pixel pitch), a COB light source behind a Fresnel lens, and an ACF release film that allows 120 mm/h on high-speed resin — in a 153.4 × 87 × 165 mm envelope.
Read that spec list against the £190 machine and you can see the family resemblance and the cuts. Same envelope. Same ACF film approach, which is the part that decides how often you are draining a vat to change film. What the base model gives up is speed headroom and the Ultra's heater, and the heater is not a luxury in a British garage in February: cold resin is viscous resin, and viscous resin fails prints.
The Ultra listing, for reference, is Photon Mono 4 Ultra at £250 with 4.3 from 72 ratings.
The faults that are documented for this family
Printer-Hub catalogues 35 model-specific issues for the Mono 4 Ultra. Several of them are the kind that make a first-time resin buyer conclude the printer is broken when it is not: the machine refuses a file because of its format, false residue alarms triggered by the strain gauge, no firmware available to download at all, and a Z-axis that whines. The site's own summary is fair — the printing itself is genuinely good, and what piles up around it is a set of gotchas the manual skips or documents for a different machine.
The Industrial Maker's field notes on the same platform focus on continuous use: the spring-loaded levelling assembly, the ACF film, and the localised heater all have maintenance intervals that matter at 100+ hours a week and barely matter at five. If you print two evenings a week, most of that page is not about you.
That is the honest shape of the risk here. £190 buys a printer whose optics are fine and whose documentation is thin. You will spend more time on forums than a Bambu Lab owner spends, and you will be rewarded with prints that cost a fraction per model.
The costs nobody puts in the review
A resin printer is not a £190 purchase, it is a £190 entry fee. You need nitrile gloves by the box, isopropyl alcohol by the litre, a wash-and-cure station (Anycubic sells one; the Wash & Cure units are routinely recommended alongside this class of printer), a silicone mat, paper towels, and a ventilated space that is not the room where you sleep.
Budget £80 to £120 for that kit on top of the printer, and budget the space for it. Resin printing in a bedroom is a bad idea for reasons that have nothing to do with the machine's quality — the fumes are real, the liquid is a skin sensitiser, and uncured waste cannot go down a drain.
Then there is the consumable curve. A 153 mm-wide vat holds roughly 200 ml, which is enough for a batch of miniatures and not much more. At £25–£35 a litre for standard resin, a hobbyist printing weekly spends more on resin in a year than the printer cost.
Resolution versus workflow
The reason to buy a resin printer at all is detail. A 10K panel across a 153 mm width works out to roughly 17 microns per pixel, which is finer than the layer heights most people print at. In practice that means edge definition on small parts — a sword, a face, the teeth on a gear — that no £190 FDM machine will match.
The reason not to buy one is everything else. Supports leave marks that need sanding. Hollowed models need drain holes or they split. A failed print means filtering resin back through a mesh filter, scraping the vat, and starting again — a twenty-minute tax on a mistake that an FDM printer charges you two minutes for.
PCMag's review of the much larger Photon Mono M7 Max makes the same point from the other end of the range: the machine is excellent, and the printing process still demands gloves and patience. Money buys speed and build volume in this category. It does not buy a clean workflow.
Who should buy the £190 one
Buy it if you already know you want resin detail and you have a garage, a shed or a utility room with a window. Buy it if your models are small — miniatures, jewellery masters, small mechanical parts under 150 mm. Buy it if you are willing to read a fault list before you read a review.
Do not buy it as a first 3D printer. A £190 FDM machine will teach you slicing, tolerances and patience with none of the chemistry, and you can decide about resin later with actual experience behind the decision.
Do not buy it if you need to print large single-piece props. The 153 × 87 × 165 mm envelope is a hard limit, and the Mono 4 Ultra and M7 Max exist precisely because people hit it.
Verdict
At £190 the Photon Mono 4 is the cheapest credible way into high-detail resin printing in the UK, and its 4.1 from 102 ratings is a realistic average for a machine that works well and documents itself badly. The 10K-named listing at the same price with 4.5 from 43 is the one to check first — if it is genuinely the higher-resolution panel for the same money, there is no reason to buy the other one.
Spend the remaining budget on the washing and curing kit and a decent respirator mask, not on a bigger printer. The bottleneck for the first six months will be your workflow, not the machine's resolution.