Anycubic Photon Mono 4 Ultra vs Photon P1 14K: which resin 3D printer fits a small workshop?
£250 against £500. Same brand, same resin process, twice the money. The ANYCUBIC Photon Mono 4 Ultra is the compact high-speed machine, the Photon P1 14K is the larger, higher-resolution one with dual-material capability. The gap that matters is not print quality. It is how much fiddling you are prepared to do.
That is the honest summary after reading through the documented failure modes of the Mono 4 Ultra, which are unusually well catalogued for a machine at this price.
The Mono 4 Ultra in numbers
A 7-inch monochrome LCD at 10K resolution — 9024 × 5120 pixels, 17 µm pixel pitch — a 153.4 × 87 × 165 mm build volume, a COB light source behind a Fresnel lens, and an ACF release film. Anycubic rates it at up to 120 mm/h on high-speed resin. That speed is the whole pitch.
The Wash and Cure 3 Plus at £189 is the natural companion — 328 ratings at 4.7 stars on the UK listing, which is the most-reviewed item in this whole resin cluster. Post-processing is not optional with MSLA, and buying the wash-and-cure unit at the same time as the printer saves a second shipping cycle.
The Mono 4 Ultra's real problem: its own file format
printer-hub.ru maintains a list of 35 documented faults for this specific model, and the first one is the most common: the printer refuses your file. The Mono 4 Ultra reads .pm4u files only. The base Photon Mono 4 uses .pm4n, the M7 uses .pm7, the M7 Pro uses .pwsz. They are all called slicer files. They are not interchangeable, and renaming one does nothing because the internal structure differs.
The second half of that problem is slicer version. Anycubic Photon Workshop 3.1.4 saved slices as .pwma instead of .pm4u — an owner on the German drucktipps3d forum documented this — and you need 3.6.3 or later for on-device exposure calibration anyway. In the machine settings, the Sliced File Suffix field must read pm4u. If you miss that field, you get “File format error” and assume the printer is broken.
Third-party slicers add another layer. Anycubic's own FAQ requires that you match the Workshop slicing mode and disable vector output when using ChituBox, Tango or Lychee — vector slicing only works in the native slicer. There is no official PrusaSlicer profile; a profile exists in UVtools but it is generated by UVtools, not by Prusa or Anycubic.
USB drives, UVtools, and the traps that ruin a batch
printer-hub documents an outright contradiction in Anycubic's own documentation about USB drives: the Ultra's printed manual and Quick Start Guide say the drive must be 64 GB or under, while the troubleshooting page linked from the product hub says the printer cannot read a drive of 32 GB or more. The safe path, per that documentation, is FAT32 with a 4096-byte allocation unit, file in the root directory (the printer does not read folders), plain English filenames under 15 characters, and an eject before you pull the drive.
The UVtools issue is worse because it looks like a hardware fault. The symptom: a model prints completely, then the job hangs on the final layer and you cannot tell whether it was exposed. The same file sent straight from the drive without UVtools processing finishes normally. printer-hub traces this to the per-layer settings flag UVtools writes, and quotes the UVtools maintainer's position plainly — global parameters can be changed, per-layer parameters cannot. Change exposure globally and the problem disappears.
Why 120 mm/h is not a free lunch
The Industrial Maker has published a field-level breakdown of this printer's mechanics, and the physics section is the part worth reading before you buy.
Their calculation uses the Stefan-Reynolds equation for parallel plates separating in a viscous fluid — which is what peeling a cured layer off the film actually is. For an 80 × 50 mm solid plate (0.004 m²) in resin at 0.8 Pa·s viscosity and a 100 µm boundary gap, the theoretical peel force at a 2 mm/s lift comes out at roughly 12,223 N. At the Ultra's 8 mm/s lift, the same part produces roughly 48,892 N. Four times the lift speed, four times the mechanical pull — on your supports, on the Z-axis rail, and on the screen underneath. In the real world the film flexes and the numbers are far lower, but the ratio holds. Cold resin raises viscosity, and bigger cross-sections raise area; both push the force up further.
That is why the comments about this machine's mechanics are not nitpicking. The Industrial Maker notes the cantilevered Z-axis runs on a single MGN12 linear rail, which allows up to 0.03 mm of torsional play (yaw) at the outer margins of the build plate under maximum peel force. The build plate uses a spring-loaded ball-and-socket clamp instead of four levelling screws — convenient, and prone to 0.05–0.15 mm of microscopic slippage under uneven off-centre peeling. Their figure for the ACF film is micro-pitting and localised clouding after roughly 25,000 layers, and they note that the mono LCD's operating lifetime drops by about 35% if chamber temperatures stay above 45°C. Heat under the LCD is a real variable on this platform.
None of this makes the Mono 4 Ultra a bad printer. It makes it a printer that wants shorter high-speed runs, good ventilation, fresh film and a levelling check every few weeks.
Where the P1 14K changes the deal
The Photon P1 sits a tier up. It is a 14K machine — roughly double the horizontal resolution class of the Ultra's 10K panel — with a larger 8.78 × 4.96 × 9.05 inch platform, Auto-Leveling 3.0, and dual-colour or dual-material printing in the variants we list. TechRadar's deals coverage singles out the Photon P1 as a resin printer that “delivers finely detailed prints for model-making”, which is the right framing: this is the machine you buy when detail and material flexibility matter more than unit cost.
What you do not get is speed. The P1 is not marketed around a 120 mm/h figure, and the combination of finer pixels and a bigger vat means longer per-layer times in the same conditions. If your workload is batches of small functional parts, the Ultra's speed is the more valuable specification. If it is single display miniatures where surface detail is the product, the P1's resolution is.
Which one to buy
Printing mostly at 0.05 mm or thicker, small to mid-size models, a few hours a week, and you want the machine working rather than tuned: the Photon Mono 4 Ultra at £250. Budget the wash-and-cure unit as part of the purchase, read the .pm4u requirement before your first slice, and set exposure globally rather than per layer.
Printing display pieces where surface finish decides whether the model is sellable, using two materials or colours in one build, and willing to spend £500: the Photon P1 14K. The resolution jump is not marketing at this scale — 14K versus 10K on comparable screens is visible on small features.
If you are unsure, start with the Ultra. It is the cheaper mistake, the documentation around it is now extensive enough that most problems have published fixes, and the resale market for resin printers this size is active if you outgrow it within a year.