Anycubic Photon Mono 4 vs Mono 4 Ultra: is £60 worth Wi-Fi on a resin 3D printer?
£190 against £250. Same 10K panel, same 153 × 87 × 165 mm build volume, same 17 µm pixel pitch. The £60 gap buys you a bigger touchscreen, a network connection, and a faster motion system — and nothing at all in print resolution. That single fact decides the purchase for most people, and it is buried under two nearly identical product pages.
The base Mono 4 is a 7-inch 10K mono LCD machine, 9024 × 5120 pixels, using a LighTurbo parallel LED array rather than the COB setup on some earlier Anycubic units. Anycubic lists 50 mm/h as standard and up to 70 mm/h with its high-speed resin. It ships with a 2.8-inch touchscreen, takes files on a USB stick, and does not have Wi-Fi, LAN, auto-levelling, resin-level sensors, or cloud slicing.
That list of absences is the entire character of the machine. It is a manual resin printer in the traditional sense, and it costs £190.
What the £60 actually changes
The Ultra keeps the panel and the build volume, swaps the 2.8-inch screen for a 4.3-inch one, adds Wi-Fi and LAN with the Anycubic app, and claims print speeds up to 120 mm/h. It also uses an ACF release film and a spring-loaded levelling assembly, both of which matter more in continuous use than they do in a first-week review.
So the honest breakdown: if you print in a shed or a garage and walk files out on a USB stick, the network connection is a feature you will use twice. If the printer lives next to your desk and you slice on a laptop, sending a job over Wi-Fi instead of copying to a stick and carrying it over is the difference between printing on a whim and not printing.
The speed figure is the more interesting one. Doubling the mm/h rating does not halve your print times, because lift, retract and settle still consume most of the layer cycle on a resin machine. What it does is make the difference between an eight-hour overnight print and a five-hour one — which, if you print miniatures in batches, is the difference between two batches a week and three.
The file format problem nobody warns you about
Both printers read Anycubic's own .pm4n slice format and nothing else. Not STL, not OBJ, not a generic .ctb from another slicer unless the workflow supports it. The base model is also picky about the USB drive itself: it will not read STL files directly, it struggles with long filenames and special characters, and it ignores files nested inside folders.
The most common beginner complaint on this model is exactly this — the file is on the stick, and the printer says "File format error" or "Failed to open file." The fix is boring: format the stick as FAT32, keep filenames short and ASCII, put the .pm4n in the root directory, and use a drive of 32 GB or less.
On the Ultra, the same limitation applies to the slice format, but the network path removes half the annoyance. That is worth something, and it is worth more than the screen size.
What actually goes wrong
Two failure modes are documented across owner reports for the base model: prints lifting in the centre of the plate, and a dark exposure screen on older firmware. The first is a levelling and release-force problem, the second a firmware fix. Neither is a hardware design flaw, and both are solvable in an afternoon.
The one that is not solvable is panel lifespan. A 10K mono LCD is a consumable — typically rated in the low thousands of hours, and every hour of exposure is an hour off the end of its life. On a £190 machine, a replacement panel is a meaningful fraction of the purchase price. Budget for one replacement across the machine's life and the economics still work; assume the panel lasts forever and you will be disappointed.
The Ultra has its own set of field issues, reported by workshops running it at volume: dimensional drift under continuous cycles, premature film failure, and layer separation when running at the higher speed settings. The pattern is obvious — the Ultra is not a better-built machine, it is a faster one, and speed exposes mechanical tolerance. If you buy the Ultra for speed, plan on maintaining it like a machine that runs fast.
Does 10K resolution actually matter?
At 17 µm pixel pitch across 153 mm, the answer is yes for miniatures, jewellery patterns and anything with fine surface detail, and no for terrain, functional parts and anything you are going to sand. The jump from 2K to 8K was transformative. From 8K to 10K is a refinement, and both of these machines sit on the refined side of that line.
What limits print quality on either model is not the panel. It is exposure calibration, resin temperature, and how well you support the model. A well-supported print on the £190 machine will beat a badly-supported print on the £250 one every single time.
Which one to buy
Buy the Photon Mono 4 at £190 if this is your first resin printer, if you print a few times a week, and if you would rather spend the £60 on resin — which at £25 to £40 a litre is two bottles, and two bottles is a lot of failed calibration prints you are allowed to make while learning.
Buy the Mono 4 Ultra at £250 if you already own a resin printer and know you will use the network path daily, or if batch throughput is the constraint rather than budget.
One thing to check before ordering: both models appear under several listing titles that differ only in wording — "10K Resin 3D Printer", "Resin printer", "Resin 3D Printer Up to 120mm/h". The one you want to avoid is the older non-10K Photon Mono 4 listing, which sits at the same £190 and has a visibly lower rating count. Read the spec line, not the price.