Anycubic Wash & Cure 3 Plus vs Photon Mono 4 Ultra: the resin 3d printer and the post-processing kit you cannot skip
£439 buys both. The Anycubic Photon Mono 4 Ultra is £250 with 4.3 stars from 72 Amazon UK ratings, and the Anycubic Wash & Cure 3 Plus is £189 with 4.7 stars from 328 ratings. They do not compete. One prints, the other finishes, and a resin print that skips the second step is not a finished part — it is a wet, sticky, mildly hazardous object that will deform over the next few days.
That is the reason this comparison is worth writing. Almost nobody regrets buying the printer. Plenty of people underestimate the second purchase.
What the Wash & Cure 3 Plus does that a bowl of IPA does not
Resin printing has three post-processing steps: remove the part from the build plate, wash uncured resin off it with isopropyl alcohol, then cure it under UV so it reaches its final hardness. You can do all three by hand with a container and a nail lamp. You will do it worse.
Anycubic's station combines wash and cure in one housing, and the 3 Plus is the version worth having. 3Dnatives' round-up of wash and cure stations describes the unit as offering 8.4 litres of volume — around 25% more than the model it replaced — with a cleaning tank measuring 230 × 140 × 260 mm. That is big enough for the build volume most hobby resin printers actually produce, which is the practical detail: a wash tank narrower than your build plate means printing smaller than you can.
Curing happens on a double tray with new gooseneck lamps, which 3Dnatives notes increase energy output so detailed areas get treated properly rather than shadowed. A touchscreen handles mode selection — cleaning, hardening, lamp control — which sounds trivial until you have used a washer with a single dial and guessed at timings. Tom's Hardware includes the same unit in its Anycubic deal coverage under the heading "Resin print post-processing", and 4.7 stars from 328 ratings is the strongest evidence on this page by a wide margin: it is the accessory that buyers rate highest, not the printers.
The tank is not sealed, so you still need ventilation and gloves, and the alcohol needs replacing periodically. It is a better tool, not a fume-free one.
What £250 buys in the printer
The Photon Mono 4 Ultra is quoted at up to 120mm/h print speed, which is fast for the money and roughly the point of the model. 4.3 stars from 72 ratings is a thinner sample than the wash station's 328, and that is normal for printers — fewer people buy them, and unhappy buyers are louder. If you want the cheaper entry, the plain Photon Mono 4 at £190 with 4.1 stars from 101 ratings prints at 6.04 × 3.42 × 6.49 inches and gives up some of the speed. The Ultra at £250 is a £60 upgrade for a much faster machine, and if you plan to print more than a handful of miniatures a month that premium pays for itself in time rather than resin.
What the listing does not tell you is the real operating cost. Resin runs £25 to £40 a litre, IPA for the wash tank a few pounds a litre and needs replacing, and you will want nitrile gloves and eye protection as consumables rather than one-offs. A first-year resin setup typically costs half again the printer's price. That is not a reason to avoid it. It is a reason to buy the £190 printer and the £189 wash station together rather than the £250 printer and no way to finish anything.
The alternative you should price first
Anycubic is not the only option, and 3Dnatives' comparison lists the competition in the same volume class. Creality's UW-02 cures parts up to 300mm tall on a rotating platform with 385nm and 405nm dual-band LEDs, but its wash tank is 250 × 160 × 200 mm — a different shape, not a bigger one. ELEGOO's Mercury XS splits wash and cure into two units with a 7-litre sealed water tank and a maximum cure size of 200 × 260 mm, plus a handheld UV lamp for interiors. The Anycubic's 8.4 litres and single-housing design is the reason it is usually the default at this price.
One thing to check before ordering any of them: the cure chamber height against the tallest thing you intend to print. A 300mm curer and a 260mm curer are not interchangeable once you start printing figurines with bases.
What to buy, in order
If you are starting from zero and have £440, buy the Photon Mono 4 Ultra and the Wash & Cure 3 Plus together, plus a litre of resin and a litre of IPA. Skip one and you own half a workflow.
If you are tightening the budget, drop the printer to the Mono 4 at £190 and keep the wash station. The wash station is not the place to save £100, because it is the part buyers rate highest and the part that determines whether your prints come out clean and hard or tacky and warped.
If you already own a resin printer without a wash and cure setup, buy the station before you buy another printer. It will improve the output of the machine you have more than a new machine would.
We have not tested either product. Prices, ratings and rating counts come from the Amazon UK listings on the day of writing; technical details are taken from 3Dnatives' comparison of wash and cure stations, Tom's Hardware's coverage and the manufacturers' published specifications, never from our own testing.