PrintVerdict

Anycubic Wash and Cure 3 Plus at £189: The Resin 3D Printer Accessory That Decides Your Workflow

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

£189 for a machine that does not print anything. That is the entire pitch, and it is also why so many resin printers end up gathering dust. The Wash and Cure 3 Plus costs almost exactly the same as the Photon Mono 4 resin 3D printer sitting at £190 — so the real question is not whether the station is good, but whether you buy it before or after the printer.

Anycubic's listing carries a 4.7 average from 328 ratings, which is unusually high for a post-processing accessory. Nobody gives five stars to a bucket out of enthusiasm. They give five stars because the alternative was scrubbing parts in a jam jar.

What the 3 Plus actually changed

3Dnatives, which catalogues wash-and-cure stations by manufacturer, lists the specifics: 8.4 litres of working volume, 25% more than the previous model, with a cleaning tank measuring 230 x 140 x 260 mm. The curing side uses a double tray and new gooseneck lamps that raise the energy delivered to the part, and the whole thing runs from a touchscreen with modes for washing, curing and lamp-only operation.

Those numbers matter for one reason: build volume. The Photon Mono 4 has a build area of 6.04 x 3.42 x 6.49 inches, roughly 153 x 87 x 165 mm. The 3 Plus tank swallows that with room to spare, which means you can drop the whole build plate in rather than handling wet parts one at a time. That single detail is the difference between a ten-minute cleanup and a forty-minute one.

The 25% volume increase over the older model is the sort of upgrade that only makes sense if you have used the smaller one. Washing works by agitation and immersion; a tank that barely fits the part moves less fluid around it and cleans worse. More volume is not a spec-sheet flex, it is functional.

Why post-processing decides whether you keep printing

Resin printing has an awkward property that FDM does not: the printer can produce a perfect part and you can still ruin it in the next ten minutes. Uncured resin on the surface is a skin irritant, the part stays tacky until it is cured, and the washing step is where most beginners discover they need isopropyl alcohol by the litre rather than by the bottle.

Do the arithmetic before you order. A wash station with an 8.4-litre capacity takes several litres of IPA to fill to a useful level, and that IPA gets saturated with resin and needs replacing. Anycubic sells water-washable resin at £14 to £26 per kilo on the same site, which is the cheaper path — but water-washable resin has its own trade-offs in strength and detail, and you cannot mix the two in the same tank without emptying it.

This is the hidden cost nobody puts on the comparison table: £189 for the station, then a recurring consumable bill that can exceed the station's price within a year if you print steadily.

Where it sits against the alternatives

3Dnatives' roundup of wash and cure stations puts the Anycubic unit in a field that splits into two groups: all-in-one boxes like this one, and separates where you buy a wash tank and a cure chamber individually. The separates usually win on tank size — Elegoo's Mercury XS, for example, carries a 7-litre sealed wash tank with a 200 x 260 mm cure area — while the all-in-ones win on floor space and cabling.

For a desk in a spare room, one box with one power cable is worth more than the extra litre. For a workshop running batches, the reverse is true.

Tom's Hardware's Black Friday coverage lists the Anycubic Wash & Cure 3 Plus among its post-processing picks alongside the Kobra and Photon printers, in a promotion running up to 39% off. That is worth noting for timing: this is a product that gets discounted in sale windows, and £189 is not necessarily the floor.

The complaints worth knowing

At 4.7 from 328 ratings, the failure pattern is thin — but two structural issues come with this category rather than this model, and neither is fixable with firmware.

The first is evaporation. An open tank of IPA loses volume to the air between sessions, and a lid that does not seal turns a £25 refill into a monthly cost. The second is resin sludge. Wash tanks accumulate a layer of dissolved resin that eventually cures on the tank walls under any UV exposure, and cleaning it out is a genuinely unpleasant job. Buying a station does not remove that chore; it moves it.

Neither is a reason to skip the station. Both are reasons to keep it away from a window.

The buying order I would recommend

If you are starting from zero with a budget of about £400, the order matters more than the individual choices. Printer first — the Photon Mono 4 at £190 is the entry point, and the Mono 4 Ultra at £250 buys speed you will not use in month one. Then resin, then IPA, then the wash and cure station.

If you already own a resin printer and are washing parts in a container by hand, the station is the single biggest quality-of-life upgrade available, and it will make you print more often. That is not a small thing: the most common reason resin printers stop being used is that the cleanup became a barrier.

At £189 the economics are simple — roughly the price of one mid-range miniature commission, or nine kilos of resin. If you print more than a couple of models a month, it pays for itself in avoided ruined parts.

Skip it if you print rarely, if you have no ventilated space for an open tank, or if you are still deciding whether resin is for you. Buy it the moment hand-washing starts feeling like a chore, because that is the exact point where the hobby dies otherwise.

Disclosure: we have not tested this station. Specifications are attributed to 3Dnatives' wash-and-cure roundup; pricing context comes from Tom's Hardware's Black Friday coverage and the current Anycubic listings.