PrintVerdict

Kobra 4 Combo at £280 or Kobra S1 ACE 2 Pro Combo at £460: the best 3d printer for beginners, four colours or sixteen

We have not tested these machines. Nothing on this page was installed, run or measured by us. Every claim is either a published specification, a price taken from the retailer listing on the day of writing, or a summary of a named third party’s review or owner report — attributed in the text.

Both of these printers are sold as multicolour machines for people who have never owned one. The Kobra 4 Combo is £280. The Kobra S1 ACE 2 Pro Combo is £460. The difference is £180, which is roughly the price of a second ACE unit, or 15 kg of PLA.

Anycubic's own listings make the distinction look like a colour count: four against sixteen. It is not. It is two different mechanical architectures, and the colour number is the least important part of the decision.

What £280 buys

The Kobra 4 Combo pairs an open-frame bedslinger with the ACE 2 Pro, a four-slot feeder that also dries filament — the listing specifies 65 °C active drying during printing, which is the useful part. Four spools, four colours, one nozzle. Anycubic also sells it as a bare printer at £280 in another listing, so check which one you are adding to the basket: 339 ratings on the Combo listing, 923 on the other.

An open bedslinger is a known quantity. It is light, it is fast in a straight line, and it has no chamber, which means ABS and ASA will warp on anything larger than a small part. PLA and PETG are fine. The ACE 2 Pro sitting on top is the reason the machine exists at this price — a dryer plus four feeders for the money of a single-spool printer two years ago.

What £460 buys

The S1 ACE 2 Pro Combo moves to a CoreXY frame inside an enclosure, with the same ACE 2 Pro feeder and a listing that advertises up to 16 colours. That number needs unpacking: 16 colours means four ACE 2 Pro units chained, and each additional unit is a separate purchase. The printer ships with one.

The enclosure is the real upgrade, and it is worth more than the colour claim. An enclosed CoreXY holds heat, which is what makes ABS printable at all, and it contains the noise — relevant if the printer lives in a room you also sit in. The trade is access: an enclosure means reaching around a frame to clear a failed print, and it means the electronics run hotter.

The part neither listing mentions

Multicolour printing wastes filament, and it wastes it in proportion to how often you change colour. Every switch purges the old colour out of the nozzle. A four-colour model with a colour change on every layer can spend more material in purge than in the part. This is not an Anycubic problem — it is what a single-nozzle multi-material system does — but it is the reason a 16-colour machine is a worse first printer than a four-colour one for most people.

There is a second, more specific issue with this family. The Industrial Maker's field report on the Kobra 3 Combo documents two failure modes in the ACE feeder system: friction inside the PTFE tube path causing feed errors, and load-cell drift from residue on the nozzle. Their conclusion is that the hardware is more capable than the multi-material integration around it. The ACE 2 Pro is a later design, but the architecture — long tubes, a single feed path, a sensor that can drift — is the same.

And the S1 has a maintenance item in Anycubic's own wiki: the Z-axis lead screw wants cleaning and greasing about every three months, and a metallic noise above 350 mm/s is described as normal rather than a fault. That is an honest document, and it is also a reminder that an enclosed CoreXY is a machine with more screws to look after than a bedslinger.

Which one, for which beginner

If the plan is models in one or two colours, with the occasional third for a label or eyes, the Kobra 4 Combo at £280 is the right purchase. It prints PLA and PETG well, the dryer is genuinely useful in a British house in November, and £180 stays in your pocket for filament — which is the thing that actually limits what you make in the first year.

If the plan includes ABS or ASA, or the printer has to live in a shared room, the S1 ACE 2 Pro Combo at £460 justifies itself on the enclosure alone. The 16-colour capability is a funnel towards buying three more ACE units at roughly £250 each; treat the shipped configuration as a four-colour machine and the price makes sense.

The £180, in filament

£180 is about 15 kg of Anycubic PLA at £12 a kilo. A 1 kg spool prints roughly 330 metres of 1.75 mm filament, which at a typical 0.2 mm layer and 15 per cent infill is somewhere between 8 and 15 kilos of finished parts depending on how much support you generate.

Put differently: the price gap is larger than most people's first year of printing. The machine is not the expensive part of this hobby, and a beginner who spends the £180 on an enclosure upgrade later — a cheap acrylic tent costs £50, a proper one £120 — ends up with a heated space and 10 kg of filament for the same money as the enclosed printer alone.

What I would not do

I would not buy either of these as a first printer if the budget is tight and the ambition is "learn to print". A single-colour bedslinger at £180 and a £40 spool of PLA teaches you more about layer adhesion, cooling and first-layer height than four colours ever will, and the multicolour system adds a whole extra failure surface — feeding, purging, retracting — before you have learned the basics of the hotend.

I would also not pay for 16 colours on paper. Four is enough for almost every model anyone actually prints, and the fifth colour is where the waste and the feed errors start.