PrintVerdict

Anycubic Kobra S1 ACE 2 Pro Combo at £485: what 16 colours cost in wasted filament — and is it still the best 3d printer under £500?

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

Sixteen colours is the number on the box, and it is not the number you will use. The Kobra S1 ACE 2 Pro Combo ships with one ACE 2 Pro unit holding four spools; sixteen requires four of them. What most people actually run is four, occasionally eight, and the machine is priced at £485 for the four-spool version with 883 ratings behind it at 4.2 stars.

The interesting question is not how many colours it can do. It is what each colour change costs you in filament you throw away, because that is the line Anycubic does not put on the box and Tom's Hardware could not get out of the slicer.

The machine, in specs

Enclosed CoreXY, 250 × 250 × 250 mm build volume, 600 mm/s maximum speed, 320 °C hotend, 120 °C bed, automatic levelling, resonance compensation. The ACE 2 Pro is the part that matters: four spool slots, active drying up to 65 °C (149 °F) while printing, sealed storage, humidity monitoring, RFID filament identification, runout detection, and automatic refill when a spool empties.

Notes from the launch coverage: Notebookcheck reported the early-bird price at $459 with two free spools for the first 1,000 buyers, an improved hotend, and 16-colour capability only when multiple ACE units are stacked. TechRadar's deal write-up had it at $550 down from $650 and quoted their reviewer Alastair's four-and-a-half-star verdict — his phrase was "one of the best 3D printers out there". In the UK it sits at £485 across three listings that differ only in title and rating count.

Why the drying function is the underrated feature

Anyone who has printed PETG in a British winter knows the failure mode: the filament absorbs moisture, the extrusion gets stringy, and eventually it snaps inside the hotend mid-print. The ACE 2 Pro dries at up to 65 °C while it prints and keeps the spools in a sealed box afterwards. That is a genuinely useful thing to have in a machine at this price, and it is the feature I would keep if I had to give up the multi-colour part.

It also explains why the jam reports cluster around wet filament. Printer-hub's error-code guide lists 11518 "Filament clogging detected", 11511 "Feeding timeout" and 11519 "Filament tangle detected" as the three most common Combo faults, and points at wet or brittle filament and crossed spools as the usual causes. The same guide notes that Anycubic's firmware V2.6.8.8 fixed frequent PETG clogs and V2.6.9.2 optimised purge length — which tells you both that early units had a real problem and that it was software, not hardware.

The purge bill nobody quotes

Every multi-colour FDM system works the same way: to change colour, the nozzle has to be emptied of the old filament before the new one arrives. That emptied filament goes in the bin. On a model with four colours and a hundred colour changes, the waste can approach or exceed the material in the model itself — which is exactly the warning makers101 raises about the large-format S1 Max, and it applies identically here.

What makes this worse than it needs to be is the accounting. Tom's Hardware's review of the Kobra S1 is blunt: the slicer "won't tell me how much material it's going to waste, which makes setting up prints extremely difficult", and the only place you can adjust purge during a print is the printer's own touchscreen. So you cannot price a multi-colour print before you commit to it, and you cannot tune the waste from the slicer where you are actually working.

Practically: if your plan is to print keycaps, signs or figurines in four colours, budget for roughly double the filament you think you need, and design so that colours change in layers rather than in every layer. A model with a coloured top and a plain body wastes almost nothing. A model with four colours on every layer wastes enormously, and no firmware update changes the physics.

What it is genuinely good at

Single-colour printing. Tom's Hardware describes the machine itself as very dependable, with a heated spool holder they rate highly. The enclosure keeps the chamber stable and filters fumes through activated carbon, which matters if the printer lives in a spare room rather than a garage. For PLA and PETG on a 250 mm bed, this is a fast, well-behaved CoreXY machine that happens to have a colour changer bolted on.

That framing is the useful one: buy it as an enclosed CoreXY with a filament dryer, and treat multi-colour as a bonus that costs extra filament.

The reliability caveat

Creative Bloq's reviewer had two faulty Kobra S1 Combo units and eventually moved to a Bambu Lab machine, while still calling the print quality excellent when it works and the setup as quick as ten minutes. Their verdict on the ACE Pro was that it "frequently clogs, jams, and tangles filament" — and their conclusion was that it is fine for beginners on a budget but not reliable enough for business use.

Two faulty units is a data point, not a rate, and the firmware has moved since. But anyone buying an ACE-based machine for production work should assume they are the quality control.

Verdict

At £485 this is the best 3d printer under £500 for anyone who wants an enclosed CoreXY with a built-in dryer — the hardware is right, the price is right, and the enclosure is not a marketing feature at this size. The 16-colour headline is the least useful thing about it.

Buy it for one to four colours, dry your filament, keep the spools sealed, and update the firmware before your first PETG print. Check the main £485 listing — the two alternates at the same price (here and here) are the same machine, so buy whichever is in stock.