PrintVerdict

Anycubic Kobra S1 ACE 2 Pro Combo review: is it the best 3d printer under £500 once the ACE Pro jams?

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

£485. That is what the Kobra S1 ACE 2 Pro Combo costs on Amazon UK right now, with 4.2 stars from 881 ratings — and two more listings at the same £485 showing 4.2 from 794 and 4.3 from 306. Three listings, one price, three different score bases. The hardware is identical.

For that money you get an enclosed CoreXY machine with a 250 × 250 × 250 mm build volume, 600 mm/s maximum speed, a 320 °C hotend, a 120 °C bed, and a filament changer Anycubic says can reach 16 colours. On paper it is the most printer per pound in this price band. The interesting question is what happens in month three.

What the reviewers actually said

Tom's Hardware reviewed the Kobra S1 and titled it "Good printer, bad slicer". Their verdict was not that the machine is weak — the motion system and the enclosure earned their place — but that the software layer around it let the hardware down. That distinction matters when you are buying a printer for a household rather than a workshop.

TechRadar's deal coverage called the S1 ACE 2 Pro Combo "one of the best" 3D printers out there when it dropped to $550, highlighting fast four-colour printing and built-in filament drying for $100 less than the usual ask. Filament drying inside the changer is not a gimmick in the UK. A spool that has sat in a garage through an autumn absorbs water, and wet filament prints with pops, stringing and weak layer adhesion. A dryer in the changer removes an entire class of failure.

Notebookcheck's launch write-up confirmed the 16-colour claim, the enclosed chamber, the revised hotend, and an early-bird price of $459 with two free spools for the first 1,000 buyers. It also noted the obvious: 16 colours is four ACE units chained together, not something in the box.

The jam problem, with error codes

Printer-Hub maintains a dedicated page on Kobra S1 faults and it is the most useful document on this machine that Anycubic does not publish. It lists nine recurring problems, and the first is the one that defines ownership: filament jams inside the ACE Pro, surfacing as error codes 11518, 11511 and 11519.

The rest of that list reads like a warning label for multi-colour printing generally. PETG clogs, because PETG sticks to a hotend more eagerly than PLA and the changer path is long. "Huge purge waste", which is the price of every colour change on every multi-colour machine, not just this one. Camera timeouts. LeviQ levelling failures.

None of those are unique to Anycubic. The purge waste in particular is arithmetic: four colours on one model means three purges per layer transition, and no vendor has solved it. But if you are buying this specifically because it is cheap multi-colour, budget the filament accordingly. A 1 kg spool does not go as far as the slicer estimate suggests.

What £485 competes with

The Kobra X at £280 does native four-colour printing with 600 mm/s and 4.2 stars from 1,298 ratings. That is £205 less than the S1 ACE 2 Pro Combo for a machine that prints most of what a beginner will print in year one.

The Kobra X Combo is £450 on one listing and £559 on another, with different review bases — 302 and 881 ratings respectively. Native seven colours, expandable to 19.

So the honest ladder looks like this. £280 for four colours and no enclosure. £450–485 for an enclosure plus drying plus up to 16 colours. £559 for the 7-colour Combo at its dearer listing, which is only worth it if you actually print seven materials in one job.

An enclosure is the reason to step up from £280, not the colour count. ABS, ASA and any engineering filament warp without one, and a draught in a spare room is enough to ruin a four-hour print. If you only print PLA and PETG, the £280 Kobra X is the better buy and the extra £205 buys nothing you will notice.

The software caveat is the real cost

Tom's Hardware's "bad slicer" finding is the part buyers underweight. A printer is a mechanical system plus a slicing pipeline, and the second half decides how often the first half produces scrap. A weak slicer shows up as supports that fuse to the model, seam placement that ruins a surface, and colour-change logic that wastes filament you paid for.

That is fixable — OrcaSlicer and PrusaSlicer both accept custom profiles — but it is not free. Expect an evening of calibration with a temperature tower and a flow test before the machine behaves. Anyone who tells you a £485 printer is plug-and-play out of the box has either been lucky or has not printed anything with overhangs.

Should you buy it

Yes, if you want one machine that does enclosure, drying and colour, and you are willing to learn a slicer. At £485 that combination does not exist elsewhere at this size, and 4.2 stars from 881 ratings is a solid, unspectacular signal from real buyers.

No, if your ambition stops at PLA figurines. Spend £280 on the Kobra X, keep £205 for filament, and buy an enclosure tent later if you ever need one. You will print more and swear less.

Wait, if your reason for wanting 16 colours is a specific project. Four ACE units is a lot of hardware to chain, and the jam rate on the changer path is the highest-risk part of the machine. Buy the Combo, add the second ACE unit only after the first has run 200 hours cleanly.

One practical note on the three £485 listings: they carry different review averages because they are different listings, not different products. Pick the one sold and shipped by Amazon where possible — on a 20 kg machine with a filament changer, the return path matters more than 0.1 of a star.