Kobra S1 ACE 2 Pro Combo vs Kobra 3 Max V2 Combo: The Best 3D Printer for Beginners Is a Size Question
£485 for the Kobra S1 ACE 2 Pro Combo. £600 for the Kobra 3 Max V2 Combo. Both enclosed, both multi-colour, both sold by the same company, and both marketed at people buying their first printer. The difference is not quality — it is whether you want 16 colours in a 250 mm cube or four colours on a 420 × 420 × 500 mm bed.
Those two numbers, 15.6 litres against 88 litres, decide almost everything else. A bigger bed means fewer cuts, fewer joints and the ability to print a helmet in one go. More colour slots mean decorative parts that come off the plate finished. You cannot have both at this price.
The S1 ACE 2 Pro Combo: small box, absurd colour count
The Kobra S1 is an enclosed CoreXY with a 250 × 250 × 250 mm build volume, 600 mm/s maximum speed, a 320°C quick-release hotend, a 120°C bed, LeviQ 3.0 automatic levelling and resonance compensation. The ACE 2 Pro in the box holds four spools and doubles as a heated dryer running to 65°C, with temperature and humidity monitoring. Stack more ACE units and Anycubic quotes up to 16 colours.
TechRadar's reviewer Alastair gave the S1 four and a half stars and wrote that "when it comes to absolute precision, the Anycubic S1 is one of the best 3D printers out there", crediting the built-in dryer for the finish quality — dry filament going in, better surface coming out. That is the strongest argument for this machine: it is not a beginner printer that happens to be enclosed, it is a well-tuned enclosed printer that happens to be cheap.
The catch is the colour workflow. Tom's Hardware's review of the Kobra S1 is subtitled "good printer, bad slicer", and the complaint is specific: the slicer will not tell you how much filament is being purged during colour changes, so loading a big multicolour print is "a gamble". Purge volume can only be adjusted mid-print from the touchscreen, where Bambu Studio and Orca Slicer expose it properly. Their reviewer says the machine brings them "to tears every time I run a four color print" — and also that it is dependable, with very few failed prints.
VoxelMatters put a number on the waste: a 10.9 g Benchy produced 183 g of purge. Seventeen times the part weight. Each colour change costs roughly two minutes, so a one-hour model can stretch past nine hours. Firmware updates have optimised purge length since, but the physics of a single-nozzle changer do not change.
Anycubic Kobra S1 ACE 2 Pro Combo at £485 — the 16-colour headline is real, but you need extra ACE units to get past four.
The Kobra 3 Max V2 Combo: 88 litres for £600
420 × 420 × 500 mm. That is 88 litres of build volume, roughly five and a half times the S1's chamber, and it changes what you can attempt: full-size cosplay pieces, a shoe last, a drone frame in one piece, a 400 mm planter that does not need a seam and epoxy. The Combo adds Anycubic's ACE multi-filament unit for four colours, and the enclosed chamber means ABS and ASA are realistic materials rather than a warp experiment.
What you give up is colour count and, honestly, tuning. The S1 is the machine reviewers rave about; the Max V2 is the machine that fits things. If your ambition is a 350 mm model printed in six colours, neither of these solves it — that is the S1 Max at £800, which has the bigger bed and the four-spool changer but not the 16-colour stack.
There is also a cheaper route worth knowing: the Kobra 3 Max V2 without the Combo is £400. Buy that, print in one colour for three months, and add the ACE unit later if you actually need it. Most people who buy a four-colour changer print in one colour 80% of the time.
Anycubic Kobra 3 Max V2 Combo at £600 — or the printer on its own at £400 if you are not sure about multicolour yet.
What breaks on these machines, according to the people who fix them
Printer-Hub's fault guide for the Kobra S1 is the most useful page on the internet for anyone about to buy one. The recurring failure is filament jamming inside the ACE unit, surfacing as error 11518 "filament clogging detected", 11511 "feeding timeout" or 11519 "filament tangle". The first fix is a restart, which resets the feed gear and opens a gap; the second involves an S2.5 Allen key and turning the gear by hand. Wet or brittle filament is the usual cause.
PETG clogging was bad enough that early firmware caused it — Anycubic fixed it in V2.6.8.8, so update the machine before your first print rather than after your first failure. There are also camera timeouts and the occasional LeviQ levelling failure. None of this is unusual for the category; all of it is avoidable if you read the error table once.
The Max V2 inherits the same ACE ecosystem and therefore the same jam profile. What it does not inherit is the S1's slicer problem, because Tom's Hardware's complaint is about Anycubic Slicer Next's handling of colour changes — which only bites when you change colours often. On a 400 mm single-colour print it is irrelevant.
The verdict for a first printer
Buy the S1 ACE 2 Pro Combo at £485 if your first year is about learning: small functional parts, tabletop miniatures, a few two-colour decorative prints, and you want the machine that reviewers rate highest at this price. The 250 mm cube is a limitation you will hit in month eight, not month one.
Buy the Kobra 3 Max V2 Combo at £600 if you already know what you want to make and it is bigger than a shoebox. Cosplay, functional parts for a workshop, anything over 300 mm. The colour count will annoy you less than a bed that is too small.
Buy neither if you have not decided. Spend £400 on the bare Kobra 3 Max V2, learn on one colour, and put the £200 you saved towards filament — which, at 183 g of purge per four-colour Benchy, you are going to need.