Kobra S1 ACE 2 Pro Combo at £485 vs S1 Max Combo at £800: the best 3d printer for beginners?
Three hundred and fifteen pounds. That is the gap between the Anycubic Kobra S1 ACE 2 Pro Combo at £485 and the Kobra S1 Max Combo at £800 on the listings we track, and it is the only decision that matters if you are buying your first enclosed CoreXY machine. Both print multi-colour out of the box. Both claim 600 mm/s. Only one of them can print a full-size helmet in one piece.
The S1 Max Combo's build volume is 350 × 350 × 350 mm — a 350 mm cube, 174% more volume than the standard S1. It also gets a 65℃ actively heated chamber and a 350℃ hotend, which is a different class of machine from the £485 one even though the marketing slides look similar.
What the extra £315 actually buys
Two things you cannot retrofit. The heated chamber is what makes ABS, ASA and polycarbonate viable at this size: a 65℃ ambient keeps a large part from cooling unevenly and curling at the corners, which is the failure mode that ruins tall prints. And the 350℃ hotend with a hardened steel nozzle and titanium alloy heat break is what lets the machine run PA6-CF, PC-CF and PET-CF without chewing through a brass nozzle in a week.
Everything else on the S1 Max is the same family of hardware as the cheaper machine: LeviQ 3.0 auto-levelling with 49 measurement points, vibration compensation from an onboard accelerometer, flow dynamics calibration, a 4.3-inch touchscreen, and the ACE 2 Pro multi-material unit included rather than sold separately. ACE 2 Pro handles four colours natively and expands to sixteen with four units; it also dries filament at 65℃ while printing, which matters more on a large machine because long prints give moisture more time to ruin layer adhesion.
Both machines claim 600 mm/s and 20,000 mm/s² acceleration, with a default of 300 mm/s. Anycubic says a Benchy takes about fifteen minutes. That is a lab number on a small model; a full-bed print on the Max is a different kind of job, and owners report roughly 17 hours for one with no layer splitting.
Where the money goes wrong
The S1 Max weighs 77.8 lb — around 35 kg — and measures 21 × 23 × 19 inches. It needs a proper bench, not a desk. If your workspace is a corner of a spare room, that is the first thing to check, before any spec.
The real complaints from owners are not about print quality. They are about software and waste. The slicer is locked to Anycubic's own software rather than OrcaSlicer or PrusaSlicer, which is the single most common reason experienced users look elsewhere. The AI failure detection has a reputation for false-triggering on filament loading, and a good number of owners simply switch it off. Multi-colour jobs produce visible artefacts at colour transitions and cost real filament in purge — the ACE 2 Pro has a side-mounted waste chute to make that less painful, but it does not make the waste disappear.
The review base on the S1 Max is thin: about 20 reviews at 4.3 stars when the listing was last sampled, with owners reporting 100 to 300+ hours without problems. That is encouraging and not yet proof. Anyone claiming five-year reliability for this machine is guessing.
Why the £485 machine is the better first printer
If you are printing PLA, PETG and the occasional TPU, the S1 ACE 2 Pro Combo does everything the Max does at a smaller size and a much lower price. The 65℃ chamber is irrelevant for PLA — it can even work against you, because PLA wants cooling and an enclosed hot box makes heat creep more likely. The 350℃ hotend is irrelevant if you never go above 260℃.
What you lose is size: no full helmet, no large enclosure panels in one piece. What you keep is 16-colour capability, the same ACE 2 Pro ecosystem, and £315 in your pocket that buys a decent filament starter set, a spare hotend and a dryer.
If size is the whole reason you are buying, buy size. That is the honest rule. A 250 mm machine that cannot fit your project is not a bargain at any price.
The third option nobody mentions
There is a Kobra S1 Max without the Combo bundle at £600, and a Kobra X Combo at £505 with seven-colour native printing that expands to nineteen. The £600 S1 Max is the right answer if you want the 350 mm cube and the heated chamber but do not need multi-colour yet — the ACE 2 Pro can be added later, and buying it separately usually costs more than the £200 bundle difference, so only take this route if you are certain you will stay single-colour.
The Kobra X Combo is the wildcard. More colours than either S1, a smaller build volume, and £295 less than the Max. For anyone printing figurines and props rather than functional parts, it is arguably the better machine — and it is why "the best 3d printer for beginners" is a question about your projects, not about the printer.
Verdict
First printer, PLA and PETG, mostly small-to-medium models: S1 ACE 2 Pro Combo at £485. That is the value call and the one I would make.
Engineering filaments, large single-piece parts, or a workshop with a proper bench: S1 Max Combo at £800. The heated chamber and 350℃ hotend are the reasons, and neither can be added afterwards.
Everything in between: S1 Max at £600, then add the ACE unit when you actually need a second colour. Buying the bundle "just in case" is how people end up with four spools of filament going brittle in a cupboard.