PrintVerdict

Kobra S1 Max Combo at £800 against Kobra 3 Max V2 Combo at £600: 42.9 litres or 88, and which is the best 3d printer for beginners

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

£600 buys you either 88.2 litres of build volume or 42.9 litres inside a heated box. That is the whole decision between these two Anycubic machines, and it is a harder call than the price difference suggests — partly because the £600 printer is the bigger one, and partly because the £800 one has a feature the bigger machine cannot add later.

The maths, quickly: 420 × 420 × 500 mm is 88.2 litres. 350 × 350 × 350 mm is 42.9. The Kobra 3 Max V2 Combo is more than twice the machine by volume, and £200 cheaper.

What the extra £200 on the S1 Max actually buys

An enclosure. The S1 Max is a fully enclosed CoreXY with a chamber rated to 65 °C, and that changes which materials are realistic. ABS and ASA warp when the part cools unevenly; a 65 °C chamber slows the cooling and keeps a large flat part flat. On an open-frame printer you can print ABS — people do — but the failure rate on anything taller than a couple of centimetres is high, and the fix is not a setting.

The second thing is speed. The S1 Max Combo is quoted at 600 mm/s with the ACE multi-colour unit included. The Kobra 3 Max V2 Combo runs the same headline 600 mm/s class, but on a 420 mm bed with 500 mm of Z the moving mass is larger, and the practical acceleration limits are not the same. Neither number is a promise about a specific model; both are the ceiling a well-tuned machine can hit.

The third thing is the hotend ceiling. The S1 Max family tops out around 320 °C (Notebookcheck reported that figure for the S1 ACE 2 Pro variant), which is what you need for the higher-temperature engineering filaments. The Kobra 3 Max V2 is quoted at 300 °C, and the £769 German-market "300 ℃ Hotend" variant is explicitly sold as an upgrade tier — meaning the base spec is not the top one.

What the 88 litres actually gets you

One-piece prints that do not fit on a 350 mm bed: a full helmet, a boot, a 400 mm architectural model, a replacement panel for something domestic. That list is shorter than people expect, and it is the honest test of whether the bigger machine is right. If nothing you want to print exceeds 350 mm in any axis, 88 litres is a number on a spec sheet.

The second use is batch work. A 420 × 420 bed takes four 200 mm parts at once where a 350 mm bed takes two, and for anyone selling printed objects that is throughput, not vanity.

The cost of the size is time. A part using most of the Z axis runs for many hours regardless of speed, and the failure mode of a 40-hour print is that you find out at hour 34. Big printers magnify the value of a reliable first layer, which is why the auto-levelling and the removable PEI plate matter more here than on a small machine.

Colour: 8 against 16, on paper

The Kobra 3 Max V2 Combo is listed as up to 8-colour, which in Anycubic's system means four native slots plus a second ACE unit. The S1 Max Combo ships with one ACE 2 Pro and, in the S1 family, the ceiling is 16 colours with multiple units — a different number because the S1 uses the newer ACE 2 Pro with active drying up to about 65 °C, which is the feature that matters in a British spare room where filament absorbs water all winter.

Multi-colour is where beginners lose money. Every colour change purges filament, and purge volume scales with the size of the machine's travel path. On a 420 mm bed those purges are long. A small multi-colour figurine can consume more filament in waste than in the object, and no firmware setting eliminates that — it only reduces it.

What the reviews say, and what they do not

TechRadar and Tom's Hardware have both reviewed the Kobra S1 family, and both treat the enclosure as the reason to buy it rather than the colour system. The pattern across those reviews is consistent: the hardware is competent, the enclosure is genuinely useful for temperature-sensitive materials, and the multi-colour unit is the part with the most caveats.

For the Kobra 3 Max V2 there is less independent testing. The 11-01 price analysis on this site covers the same chassis (420 × 420 × 500, 19 kg, 800 W AC bed peaking at 90 °C, dual Z spindles, input shaping) and the notable limitation is the bed: 90 °C is comfortable for PLA, PETG and TPU, marginal for ABS, and not enough to make ASA reliable without an enclosure you do not have.

Which one to buy

Buy the Kobra 3 Max V2 Combo at £600 if the answer to "what will you print" includes anything over 350 mm, or if you print functional parts in PLA and PETG and want the largest bed per pound. It is the better value in this comparison by a wide margin, and at £400 for the printer-only version the entry price is lower still.

Buy the S1 Max Combo at £800 if you intend to print ABS or ASA, if the machine lives in a room where draughts are a fact of life, or if you want the ACE 2 Pro's drying — which in a UK climate is not a luxury. The enclosure also makes it the quieter and safer of the two in a house with children.

And there is a third option worth naming: the S1 Max without the colour unit at £600. Same 42.9-litre enclosure, same 65 °C chamber, no ACE, same price as the 88-litre combo. For anyone printing single-colour functional parts, that is the quiet best buy in this whole comparison — you give up colour and volume, and you keep the heated chamber, which is the one feature that cannot be retrofitted.