Kobra S1 Max at £600 or Kobra 3 Max V2 at £400: what £200 buys on a best 3D printer shortlist for large parts
Both of these machines exist to solve the same problem — a part that does not fit on a normal bed. The Kobra 3 Max V2 gives you 420 × 420 × 500 mm of build volume for £400. The Kobra S1 Max gives you 350 × 350 × 350 mm for £600, and 43 litres instead of 88.
So the cheaper machine has more than twice the volume. On paper that ends the comparison. It does not, because the S1 Max is fully enclosed with a 65 °C chamber, and the Max V2 is an open frame. That single difference decides which filaments each machine can actually print reliably, and it is the reason the price runs the other way.
The volume argument, in real objects
420 × 420 × 500 mm is a helmet, a full-size cosplay forearm, a printer part that spans a 400 mm span without splitting. 350 × 350 × 350 is a large vase, a drone frame, a monitor stand, most of a shoe last. The gap between them is not proportional to the numbers — height is what usually fails first, and 500 mm against 350 mm is the difference between a wearable helmet printed in one piece and one printed in four and glued.
If your parts are under 340 mm in every dimension, the volume difference is worth nothing. That is the honest test: measure the tallest thing you intend to print, not the widest.
The chamber argument, which is worth more than 43 litres
ABS and ASA shrink as they cool, and they cool unevenly when a draft hits one side of a print. An open frame in a room with a door produces exactly that. The usual workaround — a cardboard box over the printer — works about as well as it sounds: it traps heat, it does not control it, and the electronics sit inside the hot box.
A 65 °C chamber is a different proposition. It keeps the part warm between layers, which is the actual mechanism that stops layer splitting, and it lets you print engineering plastics without gambling on the weather in your workshop. The S1 Max is a CoreXY design inside that enclosure, which also means the bed moves in one axis rather than slinging the part back and forth — better for tall prints, and quieter in a small room.
If you print PLA and PETG, none of this applies. PLA in an enclosure is worse, not better, because the chamber traps heat the material does not want.
Where the ACE question lands
The Kobra 3 Max V2 Combo is £600 — the same money as the bare S1 Max — and it adds Anycubic's ACE multi-colour unit, up to eight colours on the large frame. The S1 Max Combo is £800 for the enclosed machine with colour.
So the real decision is three-way: £400 for volume, £600 for either volume-plus-colour or enclosure, £800 for both.
Tom's Hardware's review of the Kobra 4 Combo made the point that Anycubic's multi-colour system has been evolving rather than being replaced — same architecture, better firmware, better waste handling. That is a reasonable position and it is also the source of the recurring complaint. Owner reports on r/3dprinter include units where the ACE failed on its first drying cycle, which is the kind of failure that arrives before you have printed anything worth keeping.
Multi-colour on a 420 mm bed is a niche within a niche. The parts that need that volume — helmets, armour, large functional prints — are usually one colour. Buying the Combo for the volume and using colour twice a year is paying £200 for a feature that mostly adds failure points.
The numbers that matter at £400
The Max V2 runs a 300 °C hotend, which covers PLA, PETG, ABS, ASA and most filled materials, on a 420 × 420 × 500 mm frame with an 88-litre envelope. It is a bedslinger in the traditional sense: the bed moves, the part is slung. At 500 mm tall, that motion matters — tall thin prints on a slinging bed are the classic case where a part wobbles itself into a rough surface.
At £400 that is still a lot of machine for the money. The question is whether you need 500 mm of height badly enough to accept an open frame and a moving bed. For a workshop printing brackets, jigs, planters and replacement parts, the answer is usually yes.
What nobody puts in the comparison table
Noise. An enclosed CoreXY in a spare room is a background hum; an open bedslinger at 500 mm is a machine you can hear through a door. If the printer lives in a room someone sleeps in, this is a bigger factor than either specification above.
Power and warm-up. A 65 °C chamber takes time to reach temperature, and that time is added to every print in ABS. If you print one small part a week, the chamber is a tax. If you print continuously, it pays for itself in fewer failed tall prints.
Space. The S1 Max is a cube; the Max V2 is a tall frame with a bed that travels. Both need clearance, and the Max V2 needs it front and back rather than around.
Which one
You print PLA and PETG, your parts are large and flat, and the printer lives in a garage or a workshop: Kobra 3 Max V2 at £400. The volume is real, the price is the lowest per litre in the range, and the enclosure would only get in your way.
You print ABS, ASA or nylon, or the printer lives in a bedroom or an office: Kobra S1 Max at £600. You are buying the chamber and the CoreXY motion, and the smaller build volume is the price of admission.
You want both large parts and colour, and you have £800: the S1 Max Combo, because buying the ACE later costs more than the £200 difference and the firmware match is better from the factory. Buy the £600 bare machine only if you are certain you will never want colour — that confidence tends to last about three months.