PrintVerdict

Best 3D Printer for Beginners at £399? The Anycubic Kobra X Combo, 7 Colours

We have not tested these machines. Nothing on this page was installed, run or measured by us. Every claim is either a published specification, a price taken from the retailer listing on the day of writing, or a summary of a named third party’s review or owner report — attributed in the text.

Multi-colour printing used to be the feature that doubled the price. The Anycubic Kobra X Combo at £399 is the machine that stopped that being true, and the way it did it is more interesting than the colour count.

The Combo is the Kobra X with an ACE 2 Pro filament changer. Anycubic rates it at native 7 colours, expandable to 19 with additional units. The base Kobra X at £260 handles four. Both run the same 600 mm/s class motion system and the same tool head, and that last part is the point.

Why the colour swap matters more than the colour count

Tom's Hardware put the Kobra X head-to-head with a Bambu Lab A1 and timed the thing that actually governs how long a multi-colour print takes: the cut-to-purge cycle. The Kobra X averaged 35 seconds per swap. The A1 took 90 seconds or more.

On a four-colour model with 776 colour changes, that difference added up to roughly 10 hours — on prints of similar speed. Ten hours. Not ten minutes. If you print figurines, signage or anything with banded colour, the swap time is the whole experience, and Anycubic solved it by putting the filament switcher in the tool head rather than at the frame.

TechRadar's reviewer is blunt about the lineage: the Kobra X is a major overhaul, faster and better built than the Kobra 3 Combo, with a quick-swap hotend that carried over to the newer Kobra 4 Combo. The same reviewer notes the Kobra 4 does not displace the X as the budget pick. That is an unusual thing for a manufacturer's newer machine to fail at, and it says something about how well the X was specified.

What the Combo adds for £139

The £399 Combo is the £260 printer plus a four-spool changer that takes the machine to seven native colours. If you print in one colour, that £139 is dead money and the base model is the right buy. If you print in two, the arithmetic changes fast: manual filament swaps cost you attendance, not just time, because someone has to be in the room when the printer beeps.

Nineteen colours via stacked ACE units is a specification, not a workflow. Four is a workflow. Seven is a workflow with a decision to make about which seven, and most people end up with black, white, grey, and four colours they use once.

The parts nobody enjoys

Purge waste. Every colour change costs filament. The 35-second swap is fast, but it still purges, and a 776-swap print generates a waste tower that you will weigh and then feel bad about. This is physics, not an Anycubic flaw, and it applies to every multi-material bedslinger on the market.

It is open-frame. No enclosure means no ABS, no ASA, and no printing in a cold garage in January without warping. PLA and PETG are the brief.

A bedslinger is still a bedslinger. Moving the bed in Y limits acceleration and puts height-related artefacts into tall prints. Tom's Hardware's framing is exact: the Kobra X is compelling proof that bedslingers are not dead. Not that they are better.

Beginner-friendly is not the same as beginner-proof. The screen walks you through setup step by step, which is genuinely helpful in week one. It does not teach you why a first layer fails, and it will not tell you that your filament is wet.

What actually breaks, and what it costs

A quick-swap hotend is the most underrated feature on a budget printer, because the nozzle is the part that fails. TechRadar notes the mechanism carried from the Kobra X to the newer Kobra 4 Combo, which is a good sign: a design that survives a generation is a design that works.

Consumables are the running cost. Filament at £12 to £18 a kilo, a nozzle every few months, a build plate after a year of bad first layers. On a multicolour machine add the purge waste, which on a heavily banded print can reach 30 per cent of the filament you bought.

Noise is the other practical limit. A bedslinger at speed in a spare room is audible through a wall. Anyone planning to print overnight in a flat should plan for that, and a concrete slab under the feet does more for the money than any enclosure.

The beginner question in the title

Is this the best 3D printer for a beginner at £399? For a beginner who wants colour, yes — nothing else at this price does seven materials with a 35-second swap, and both Tom's Hardware and TechRadar rate it at or near the top of the budget class.

For a beginner who wants to learn the craft on one colour, no. The base Kobra X at £260 teaches the same lessons for £139 less, and a spool of good PLA costs £18. That £139 is better spent on filament and a filament dryer than on a changer you will use for one project and then leave loaded with dust.

The honest split: buy the Combo if you already know you want multicolour, buy the base model if you are still finding out. The most common mistake in this hobby is buying the feature you have not yet needed.

Our judgment, separated from the facts

No printer was run for this page. The 35-second swap, the 90-second A1 comparison, the 10-hour saving across 776 swaps and the 600 mm/s class speed come from Tom's Hardware's testing; the build-quality and hotend observations come from TechRadar's review; the colour counts and prices are Anycubic's listing on the day of writing. The recommendation to start with the £260 base model is ours, and it is the part a multicolour enthusiast would argue with.

At £399 the Kobra X Combo is not a beginner toy that happens to print in colour. It is a competent printer that happens to be the cheapest serious route into multicolour, and those are two different claims.