PrintVerdict

Kobra X Combo at £430 or Kobra 4 Combo at £300: the best 3d printer for beginners, £130 apart

We have not tested either printer. No machine was assembled, calibrated or run by us. Prices and rating counts come from our own UK feed; build volume, nozzle and drying details are Anycubic's published specifications as reported by Tom's Hardware and TechRadar. Review conclusions are quoted from TechRadar's Kobra X test by Alastair Jennings and Tom's Hardware's Kobra 4 Combo review.

Two Anycubic printers, both four-colour, both sold as a Combo. £430 and £300. Same manufacturer, same target buyer, same 260 mm-class build volume — and completely different ideas about where the filament should change colour.

That is the only thing worth understanding before you spend the £130.

The two mechanisms

The Kobra X Combo puts the colour changer in the toolhead. Four filaments feed a compact unit that travels with the print head, so the change happens centimetres from the nozzle. The Kobra 4 Combo puts the changer in a box beside the printer: the ACE 2 Pro, which feeds four filaments through Bowden tubes into a single hotend.

Toolhead changers waste less filament and change faster. Box changers are simpler, hold more filament, and — this is the part the spec sheets bury — can dry it.

Tom's Hardware's review of the Kobra 4 Combo makes the drying point explicitly: the ACE Pro 2 "can double as a filament drier, which comes in handy when printing moisture-loving PETG." If you print PETG in a British house in February, that is not a small feature. A wet spool of PETG prints like a stringy mess regardless of how good the motion system is.

What the reviews say about each

TechRadar's Alastair Jennings tested the Kobra X and called it a major update to the range: faster, better built, with a redesigned touchscreen and native four-colour printing. He also flagged the two limits that matter. The open frame restricts engineering materials — no enclosed chamber means no ABS or ASA without warping. And you need to keep the RFID sticker close if you want to use non-Anycubic filament, which is the kind of detail that turns a £20 saving on a spool into an afternoon of troubleshooting.

Tom's Hardware's verdict on the Kobra 4 Combo is more measured: an updated Kobra 3 that takes styling from Bambu Lab's A1. Quick-swap high-flow hardened steel nozzle, excellent auto bed levelling, vibration compensation, "a solid machine and a good value." Their criticism is about ergonomics, not output — the Kobra 4 is "a bit unwieldy when compared to the clean filament paths and slender footprint of the Kobra X." Both machines, they note, have excellent print quality.

That last sentence is the one to remember. You are not choosing between good prints and bad prints. You are choosing between two ways of getting good prints.

The £130, itemised

What the extra money buys on the Kobra X Combo:

What the £300 machine buys instead:

The thing nobody mentions

Both of these are open-frame bed-slinger designs. That is fine for PLA and PETG, which is what 90% of beginners print. It is not fine for ABS, ASA or polycarbonate, and no amount of colour-changing hardware fixes it. If your reason for buying a printer is functional parts that live outdoors or in a car, neither of these is the right machine and the £130 question is irrelevant.

There is also a support consideration that comes up repeatedly in owner reports. A public r/3Dprinting post about the Kobra X — titled bluntly, and written by someone who had also bought an Anycubic resin printer — describes a print head that "is not built for repair, yet it often needs repair", and customer service that was "spotty, condescending at times". One angry owner is not a reliability statistic, and the same post praises the machine's first months. But it is the pattern to check before you buy: how easy is a hotend swap, and who pays for the part.

On the Kobra 4, Tom's Hardware answers part of that: the quick-swap hotend is shared with the Kobra X, and it is a genuine improvement over the older Kobra 3.

Why both machines show the same review count twice

Our feed lists each Combo twice, and the two listings for a given machine carry identical rating counts — 904 and 331 for the Kobra X Combo, the same pair for the Kobra 4 Combo. That is not a coincidence and it is not a scam: they are colour variants of one product page, so the reviews pool. When you compare them, compare the machine, not the listing.

It also means a "4.2 stars from 904 ratings" figure is a blend of everyone who bought either colour, which is a more honest number than a single variant's 40 reviews.

Which one

For a first printer bought to make multicoloured models — miniatures, toys, decorative parts — the Kobra X Combo at £430 is the better machine. Less waste, smaller footprint, and the design that Anycubic's own reviewers treat as the current generation.

For a first printer bought to make functional parts in PLA and PETG, with colour as a bonus, the Kobra 4 Combo at £300 is the better buy. The ACE 2 Pro's drying function will save you more failed prints than the toolhead changer will save you filament.

And if you genuinely do not need four colours, buy neither Combo. Both are sold as single-colour machines for around £259 to £279, and the second, third and fourth colour is where most of the money goes.