Kobra X Combo vs Kobra S1 ACE 2 Pro Combo: the best 3D printer for beginners in the UK?
Two Anycubic machines, same brand, £74 apart, and the cheaper one has more colours. The Kobra S1 ACE 2 Pro Combo is £485 with a 16-colour filament system and a fully enclosed CoreXY frame. The Kobra X Combo is £559 with native 7-colour printing that can be pushed to 19. On the spec sheet, the S1 looks like the obvious buy. It mostly is — but not for the reason the spec sheet suggests.
Start with the sizes, because that is where the two machines genuinely diverge. The S1 ACE 2 Pro builds in 250 × 250 × 250 mm. The Kobra X Combo is the larger-format option in Anycubic's current line and prints faster on paper at 600 mm/s. For a beginner printing models, brackets, toys and the occasional functional part, 250 mm cubed covers almost everything. For anyone printing helmets, cosplay armour or large single-piece props, it does not, and no amount of colour technology fixes that.
What the extra £74 buys on the Kobra X
Colour handling, mostly. The Kobra X Combo runs what Anycubic calls native 7-colour printing expandable to 19 with additional ACE units. TechRadar's review of the base Kobra X found it beginner-friendly and surprisingly good for a four-colour machine — the review unit was the 4-colour version, and the Combo adds the multi-colour box on top.
That gap between 7 and 16 colours is smaller in practice than it looks. Almost nobody prints 16 distinct colours in one object. Most multi-colour prints use three to five, and the rest of the slots exist so you can keep different materials loaded — PLA for the model, PETG for a functional insert, a transparent filament for light pipes. Buying colour capacity you will never use is the most common way beginners overspend on a first printer.
Why the enclosed S1 wins for a UK buyer
This is the argument that actually decides it. The S1 ACE 2 Pro is a fully enclosed CoreXY. An enclosure does three things: it holds heat, it blocks draughts, and it keeps dust and cat hair off the build plate. In a British garage, shed or spare room, where temperatures swing between 8 °C in January and 30 °C in a heatwave, an open-frame printer warps large ABS and ASA parts and struggles with dimensional accuracy on big PLA prints near a window.
The Kobra X Combo is an open-frame design. That is fine for PLA, and PLA is what 90 percent of beginners print. But the moment you try PETG on a cold day or ABS at all, the enclosure stops being a nice-to-have. If the printer lives in a heated indoor room, this whole paragraph does not apply. If it lives anywhere else in the UK, it probably does.
TechRadar's coverage of the S1 ACE 2 Pro Combo noted fast four-colour printing and integrated filament drying in the same unit. Drying is underrated: UK humidity ruins PLA and PETG left on a spool for weeks, and a dryer built into the filament station removes one more accessory you would otherwise buy.
Prices, and which listing to pick
The S1 ACE 2 Pro Combo at £485 carries 4.2 stars across 881 ratings. The Kobra X Combo at £559 also carries 4.2 across 881 — the same review pool, split across listings.
There is a third option worth knowing: the Kobra X without the multi-colour box at £280, with 4.2 stars and 1,298 ratings. That is the cheapest way into a 600 mm/s machine, and it prints single-colour parts identically to the Combo. If colour is a maybe rather than a must, £280 now and a colour unit later is a defensible path — the ACE boxes are sold separately and the firmware supports adding them.
Anycubic also lists the Kobra X Combo at £450 on a separate listing with 4.3 stars across 302 ratings. Two prices for the same hardware, £109 apart. Check both before ordering; the lower one is not always in stock, but when it is, the £559 listing is simply worse value.
The complaint that applies to both
Anycubic's customer service has a reputation problem, and it is not limited to one model. A widely read post on r/3Dprinting from a Kobra X owner described support as "spotty, condescending at times", complained that the print head is not built for repair yet often needs it, and concluded that the machine "might work at first, but then you will be doing maintenance between every print". That is one person's account, not a survey. But it echoes what turns up repeatedly in Anycubic threads, and it applies equally to the S1.
The practical consequence for a beginner: buy from a retailer with a return window you can actually use, keep the box for a month, and expect to learn basic maintenance — nozzle swaps, hotend cleaning, belt tension. Anycubic printers are good value precisely because you are doing some of the work a Bambu Lab would do for you. Tom's Hardware's review of the Kobra 4 Combo summed up the family's cadence as "evolution, not revolution", which is accurate and also a warning: each generation is a modest step, so the previous one at a discount is often the smarter buy.
The verdict
For a UK beginner, the S1 ACE 2 Pro Combo at £485 is the better first printer. Enclosed CoreXY, filament drying in the box, 16 colour slots you will not exhaust, and 250 mm of build volume that covers beginner projects. It is also £74 cheaper than the Kobra X Combo, which makes the decision unusually easy.
Buy the Kobra X Combo instead if you need a bigger build volume, print mostly PLA in a warm room, and want the higher colour ceiling for multi-material work rather than multi-colour decoration. Buy the £280 Kobra X if you want to spend the difference on filament — which, at £18 to £25 a spool, is between four and six spools, and far more useful to a beginner than a colour box sitting at 30 percent utilisation.