PrintVerdict

The Anycubic Kobra X Combo is not the best 3D printer for ABS — and at £430 that is fine

We have not tested these machines. Nothing on this page was installed, run or measured by us. Every claim is either a published specification, a price taken from the retailer listing on the day of writing, or a summary of a named third party’s review or owner report — attributed in the text.

Anycubic sells the Kobra X in two shapes that look identical in a product photo and differ by £150. The printer on its own is £280. The Combo is £430, and the difference is the filament changer: native seven-colour printing, expandable to nineteen according to the listing.

That £150 is the whole decision. Everything else — the frame, the 600mm/s headline speed, the touchscreen — is the same machine.

What £430 does buy

TechRadar’s Alastair Jennings reviewed the four-colour Kobra X and landed on a verdict that is unusually balanced for a machine at this price: the Kobra X is a major update to the range, with faster printing and a real improvement in how the machine looks and feels, and it is “perfect for beginners and enthusiasts”. He also notes that at roughly the £300/$300 mark you are getting a machine with essentially every feature the segment offers — and that the segment is crowded with proven machines.

Tom’s Hardware, reviewing the closely related Kobra 4 Combo, describes the generational change as sitting mostly in the multimaterial handler — the ACE Pro 2 — rather than in the motion system, and calls the machine “evolution, not revolution” while still judging it a solid machine and good value.

Read those two together and the picture is coherent. The Kobra X Combo is a well-built bedslinger with a colour changer bolted on. You are not buying a new architecture; you are buying seven colours at an entry-level price.

What £430 does not buy

An enclosure. The frame is open. TechRadar is explicit that the open design “limits the potential for utilising engineering materials”. ABS and ASA warp without a stable, warm chamber, and no amount of slicer tuning fixes draughts in a garage in November. If your reason for wanting a printer is functional parts that survive heat or UV, this is the wrong machine — and no printer at £430 is the right one unless it is enclosed.

Filament freedom. This is the detail that sells machines and then annoys owners: the ACE system reads spools by RFID. Use Anycubic filament and it just works. Use anything else and you are relying on a workaround — TechRadar’s advice is to keep the RFID sticker from an Anycubic spool close, because that tag is what the changer uses to identify a slot.

A drying solution. Multicolour printing multiplies the number of open spools in the room. Wet filament prints badly and looks like a mechanical fault, which is how people end up returning printers that were fine.

The honest risk: the changer, not the printer

Creative Bloq spent about four months with the Kobra 3 V2, an earlier machine with the previous ACE unit, and the write-up is worth reading before you spend £150 on a colour changer. The verdict: it prints flawlessly in single colour and is genuinely beginner-friendly, but almost every problem traced back to the ACE unit, which “frequently clogs, jams, and tangles filament”. The reviewer had also been through two faulty Kobra S1 Combos.

Anycubic has revised the hardware since — the ACE Pro 2 in the Kobra 4 generation is the current part — and one reviewer’s experience is not a defect rate. But the pattern is consistent across budget multimaterial systems: the single-colour printer is reliable, and the changer is where the patience goes.

Which produces a genuinely useful rule. If most of what you print is one colour, buy the £280 printer and spend the £150 on filament. You will print more, waste less, and never diagnose a tangle at 11pm.

The unglamorous reason to buy from a big brand

At £430 the maths of ownership matters more than the spec sheet. Anycubic sells replacement hotends, build plates and ACE parts through its own UK store and through Amazon, which means a failed thermistor in February is a £15 order and two days rather than a three-week wait for a part from Shenzhen. That is not a feature anyone puts on a box, and it is the difference between a printer you keep for four years and one that ends up in a loft.

It also means the machine holds some resale value, which matters if you decide in six months that you want an enclosed printer after all.

Where seven colours actually earns its money

Not on the model you print once. On the things you print repeatedly with colour changes inside a single layer: signage, board-game inserts with coloured text, cosplay pieces with panel colours, teaching aids for a classroom. In those jobs, a changer removes a manual pause-and-swap step that you would otherwise do fifteen times.

For decorative multi-part prints where the colours sit in separate objects, a single-colour printer plus a £20 can of paint does the same job. That is not a criticism of the Kobra X Combo; it is a description of the jobs it is for.

Which one to order

If you have read this far and still want colour, the Kobra X Combo at £430 is the right buy — it is the cheapest way into seven-colour printing from a brand with UK support, and the single-colour fallback is a good machine in its own right. If you are buying your first printer and the honest answer to “will I print in colour?” is “probably not”, the Kobra X at £280 saves you the £150 and the learning curve.

Either way, budget for one more thing: a sealed box and some desiccant. It costs less than a spool and it prevents the single most common “my printer is broken” post on every 3D printing forum in Britain between October and March.

The short version

The Kobra X Combo is a good £430 printer for PLA and PETG in several colours. It is not the best 3D printer for ABS, it is not a closed-chamber machine, and it locks you into a filament ecosystem unless you keep a sticker. Buy it for colour, not for materials, and the machine will do exactly what you paid for.