Anycubic Kobra X vs Kobra X Combo: Is the Best 3D Printer for Beginners Worth £170 More?
Same printer, different colour count. The Kobra X is £280 with four colours out of the box. The Kobra X Combo is £450 with seven, expandable to nineteen. Everything between them is colour management: extra filament paths, extra motors, extra things that can jam at 2am.
That is the whole decision, and it is worth being blunt about it. If you print brackets, boxes, replacement knobs and the occasional planter, four colours is already more than you will use. If you print models where the colour is the point, £170 is cheaper than buying the Combo's hardware separately later.
What £280 actually gets you
A 260 × 260 × 260mm build volume, 600mm/s claimed print speed, and native four-colour printing through Anycubic's ACE system. 296 ratings at 4.3 on the beginner-focused listing, and a second Kobra X listing at 4.2 with 1,298 ratings — the larger sample is the one I would trust, and 4.2 over thirteen hundred buyers is a normal score for a budget bedslinger, not a warning sign.
TechRadar tested the four-colour Kobra X and called it surprisingly good for a beginner-friendly machine. Note the phrasing: surprisingly good is the right register for a £280 printer that handles colour changes automatically. It is not a Prusa, and no reviewer is claiming it is.
What the Combo adds, and what it costs to use
Seven native colours, up to nineteen with additional ACE units, and a 2× faster claim that refers to the multi-colour workflow rather than to raw print speed. Multi-colour printing is slow for a reason that has nothing to do with the printer's motion system: every colour change means purging the nozzle, and the purge material goes in the waste bin. A four-colour model with a lot of colour swaps can generate more waste by weight than the part itself. Seven colours multiplies the opportunities.
That is the part of this comparison that no spec table shows. The Combo does not just cost £170 more at checkout; it costs more per print in filament, and it costs more of your time in purge tuning. If you are printing a two-colour keyring, the difference is irrelevant. If you are printing a seven-colour figurine, the waste bin fills up and the print takes most of a day.
The complaint file
A thread in r/3dprinter put the problem with this product category plainly: the poster wanted a beginner printer, had watched a lot of videos about how good the Kobra X is, and noted that every review seemed to be paid by Anycubic. That is not evidence of anything except a marketing budget, but it is a fair reason to weight owner reports above launch reviews when you are spending £450.
The owner reports are less flattering. A long post in r/3Dprinting from an Anycubic customer describes a resin printer whose laminate started peeling between the cover and the machine, build-plate corners that gripped prints hard enough to leave bulges, maintenance between every print, and a print head that is not built to be repaired despite needing repair. The same post accuses the company's support of being spotty and condescending. One angry customer is not a reliability statistic. It is, however, the kind of account that never appears in a launch review, and it is consistent with what budget FDM ownership actually looks like: you are the service technician.
Tom's Hardware's 2026 printer coverage is the counterweight. Their testing programme is more systematic than most, and multicolour machines from Anycubic, Creality, Bambu Lab and Prusa all appear in their picks and deals coverage. The category is mature enough that £280 buys a working four-colour printer — the risk is not that it will not print, it is that it will need attention.
Who should buy which
First printer, functional parts, learning the craft: Kobra X at £280. Four colours is enough to make labels, two-tone cases and simple signs, and the money you save buys filament, a filament dryer and a set of nozzles — all of which will improve your results more than three extra colours will.
Miniatures, prop replicas, anything where the paint job is replaced by filament: Combo at £450. Seven colours with the option to expand is a genuinely different capability, and buying the base machine first then adding ACE units later costs more than the £170 gap. Just budget for the purge waste and accept that a seven-colour print is an overnight job, not an afternoon one.
The £559 listing of the same Combo is also in our catalogue, and the £109 difference between it and the £450 one is not explained by anything in the product description. Check which listing you are actually buying before you check out — same model name, two prices, one of them is a worse deal for identical hardware.
My call
For most people reading a page titled best 3D printer for beginners, the £280 Kobra X is the right buy. It does the thing beginners actually need — reliable single and two-colour prints in a decent volume — and it leaves £170 in the budget for the consumables and tools that determine whether you stay in the hobby past month three.
The Combo is the right buy for a narrower group: people who already know they want multicolour models and who have priced the filament waste into their expectations. If you are unsure which group you are in, you are in the first one. Buy the £280 machine, print for two months, and let your own waste bin tell you whether you need seven colours.