PrintVerdict

Photon Mono M7 Pro at £430 or Kobra 3 Max V2 at £400: a resin 3d printer against a big FDM one

We have not tested these machines. Nothing on this page was installed, run or measured by us. Every claim is either a published specification, a price taken from the retailer listing on the day of writing, or a summary of a named third party’s review or owner report — attributed in the text.

Four hundred pounds is the awkward part of the 3D printing market. It is enough to buy a very good resin printer, enough to buy a large FDM printer, and not enough to buy both. This week the Anycubic Photon Mono M7 Pro at £430 and the Anycubic Kobra 3 Max V2 at £400 sit £30 apart, and they have nothing in common except the brand on the box.

What the £430 resin machine is

The M7 Pro is a 14K MSLA printer with a 223 × 126 × 230 mm build volume and a claimed 170 mm/h print speed. That speed figure is the interesting claim, because resin printers have historically been measured in millimetres per hour the way glaciers are measured in metres per year. Anycubic gets there with a light engine and release film combination designed for fast peeling, and the result on the listing shows 4.0 stars from 101 ratings.

One hundred and one ratings is not much. The Kobra 3 Max V2 has 918. That gap matters more than the star average, because resin printers fail in ways that take twenty ratings to surface: a film that delaminates after 40 prints, a screen that dims unevenly, a vat heater that was never there. Three months of owner reports is worth more than a launch-week average.

What the £400 FDM machine is

The Kobra 3 Max V2 is a 420 × 420 × 500 mm bedslinger-ish CoreXY at 600 mm/s claimed, with 4.2 stars from 918 ratings, and it takes the ACE filament system for up to eight colours. Eighty-eight litres of build volume for £400 is, on its own, an absurd amount of machine per pound. The Combo version with the multi-colour unit is £600.

Its weakness is the one every large-format FDM printer shares: the bigger the volume, the longer a failed print wastes. A 20-hour print that detaches at hour 17 costs you 300 g of filament and a day. On a 250 mm machine that failure costs half as much.

The cost nobody puts on the comparison table

This is where the two paths diverge, and it has nothing to do with the printers. A resin workflow needs washing and curing. The Anycubic Wash & Cure 3 Plus is £150, and while you can wash in a jar of IPA and cure in sunlight, anyone who has done it for a month buys the machine. Add gloves, a respirator, isopropyl alcohol at £8–12 per litre, and a room you can ventilate.

Resin itself costs £25–45 per kilogram and you cannot print a 200 mm model on a 223 mm plate without hollowing it and adding drain holes, which is a skill. FDM filament is £12–20 per kilogram, and a failed print goes in the bin without PPE.

So the honest total for the resin route is £580 before your first print, plus consumables that cost twice as much per kilogram. The honest total for the FDM route is £400 and a spool.

What each one is actually good at

Resin wins on detail, full stop. A 14K panel at 16.8 × 24.8 micron pixels resolves things FDM cannot: miniature faces, jewellery masters, small mechanical parts with 0.5 mm features, anything where the surface finish is the point. The M7 Pro's 223 mm plate also fits a bust or a set of parts in one run, which is more than most 10-inch resin printers manage.

FDM wins on size, strength and cost per part. A 420 × 500 mm volume means a full helmet, a drone frame, a replacement bracket for a dishwasher that no longer exists. Layer lines are visible, the surface is matte and rough, and none of that matters for functional parts.

The failure modes are different too

Resin failures are usually about the film, the temperature and the supports. A cold garage in a British November will thicken resin to the point where the exposure settings on the screen are wrong, and the M7 Pro has no heated vat — the larger M7 Max does not either. If the printer lives in an unheated shed, budget for a heater or move it indoors.

FDM failures are usually about adhesion and warping. A 420 mm bed is hard to heat evenly, and large ABS or ASA parts will lift at the corners unless the enclosure holds temperature. The Kobra 3 Max V2 is enclosed, which helps, but a 500 mm tall print is still a 20-hour bet.

My recommendation

If you want to print miniatures, jewellery masters, or small parts where the surface is the product: the M7 Pro, and buy the wash and cure station at the same time. Do not try to save £150 by washing in a jar; you will spend it on IPA and ruined prints within two months.

If you want to print brackets, boxes, jigs, cosplay armour, or anything you would otherwise make from plywood: the Kobra 3 Max V2, and ignore resin entirely. The £30 you save against the M7 Pro is not the point; the £180 you save on the finishing kit is.

If you genuinely do not know yet, buy the Kobra 3 Max V2. Not because it is better — it is not, for detail work — but because it is the machine that teaches you whether you enjoy 3D printing at all, and it does so without requiring gloves and a ventilated room. The resin printer you buy second will be a better resin printer than the one you would buy today.