PrintVerdict

Photon Mono M7 Max at £699 or Photon P1 Max at £950: choosing a large resin 3d printer by volume, not by badge

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

Two Anycubic resin machines, £251 apart, and both described as large. The M7 Max gives you 14.7 litres of build volume for £699. The P1 Max gives you 18.3 litres for £950. Per litre that is £47.60 against £51.90 — so the cheaper machine is also the cheaper volume. Everything else is a trade.

The two builds

The Photon Mono M7 Max at £699 uses a 13.6-inch 7K monochrome LCD over a 300 × 297 × 165 mm build area — 11.8 by 11.7 by 6.5 inches on the UK listing, which works out to 14.7 litres. It runs the ACF release film that makes its headline speed possible, and it manages resin level automatically rather than asking you to top up by eye.

The Photon P1 Max at £950 is the 18.3-litre machine, with a smart resin tank and automatic levelling according to the listing. That is 3.6 litres more than the M7 Max for £251 more — and on price per litre it is the dearer of the two, £51.90 against £47.60. Bigger, not better value.

Below both, the Mono M7 Pro at £430 offers a 223 × 126 × 230 mm build area with a 14K panel and a 170 mm/h speed figure. 6.5 litres for £430 is £66 per litre — worse value on volume, better on detail.

What PCMag actually criticised on the M7 Max

PCMag reviewed the M7 Max at $899.99 and made it an Editors' Choice, praising the 14.7-litre volume, the light source handling 10-micron calibration files, the automatic resin management and the remote monitoring. The listed complaints were specific and small: awkward USB port and power cord placement, and a "relatively low-resolution 13.6-inch LCD print screen".

That last point is the one worth doing arithmetic on. 7K across 13.6 inches works out to roughly 476 pixels per inch; 14K across 10.1 inches is about 1,318. The big panel carries around a third of the linear pixel density, so on the M7 Pro you get finer detail on small parts, and on the M7 Max you get bigger parts at coarser pitch. If you print 28 mm miniatures, the Pro is the better machine. If you print helmets and props in one piece, the Max is the only one of the three that will hold them.

The failure modes you will meet

A 2026 troubleshooting write-up on Printer Hub catalogues fourteen issues specific to the base M7, and several carry across the family: an uneven build plate that ruins prints in the centre of the plate while the edges stick perfectly, a single strain gauge that every automatic function depends on, the trade-offs of the matte ACF film, the closed .pm7 file format, and a separate FPGA firmware update path. The same article includes the 300–314 error code table.

The centre-of-plate failure is the one that catches people. A Reddit user in r/resinprinting described exactly that pattern on an M7 Max: over a hundred prints, 70 to 80 percent of the plate fine, the centre never adhering, with the plate relevelled repeatedly, several resins tried, FEP and nFEP swapped, and the machine kept in an enclosed garage at a steady temperature. That is not a user error — it is a flatness problem, and it is the reason to check the plate with a straight edge on arrival rather than after the first failed print.

Anycubic's own wiki, for its part, treats layer lines as a maintenance item: increase lift distance, reduce lift and lower speeds, clean and lubricate the lead screw and linear guide, and never use alcohol or water on them. Ordinary advice, and it assumes you will actually do it.

Cost of ownership, briefly

ACF film is a consumable with a shorter life than FEP in some workflows, and a 13.6-inch panel is an expensive part to replace. Both facts belong in the budget. A £699 printer that needs a new release film every few weeks and a £120 screen after a resin leak is not a £699 printer over three years.

Speed claims, read carefully

The 150 mm/h class figure on the M7 Max is a peak, not an average. It assumes thin layers, a hollow model with a small cross-section, and the ACF film doing its job. A solid 300 mm tall print with thick walls spends most of its time peeling from the film, not exposing, and will land far below the headline. The same applies to the 170 mm/h figure on the M7 Pro.

What actually changes print time on a large machine is how much of the plate you fill. Four small parts on a 14.7-litre plate take the same time as one — that is the real argument for volume, not the speed number on the box.

Which one

Large single-piece prints — helmets, cosplay armour, architectural models, prototype housings — on a budget: the M7 Max at £699. It is the cheapest 14.7 litres you can buy from Anycubic, and PCMag's objections are about port placement and pixel pitch, not about it failing at its job.

A model that genuinely will not fit in 14.7 litres and cannot be split: the P1 Max at £950. 3.6 extra litres and a smart resin tank, at a worse price per litre — buy it only after measuring, not because the number is larger.

Two materials in one vat: the smaller Photon P1 14K at £499, which sells on exactly that feed arrangement. It is the one machine here that does something the others physically cannot.

Small, detailed parts where surface finish matters more than size: the M7 Pro at £430. Paying for volume you will not fill is the most common waste in resin printing.

And if you are buying your first resin printer: none of these three. A 14.7-litre vat is a lot of resin to waste while you learn exposure times, and the failure modes above are easier to diagnose on a smaller, cheaper machine.