Anycubic Photon P1 14K at £500 three times and £650 once: a resin 3d printer listing puzzle
Four listings for the Anycubic Photon P1 14K on one page. Three of them say £500. One says £650. All four describe the same 14K mono LCD machine with an 8.78 by 4.96 by 9.05 inch build volume and Auto-Leveling 3.0.
The £650 one has two words the others do not: dual colour. That is the entire difference, and it is a £150 question.
What dual colour actually means on a resin printer
Resin printing does not work like filament. There is no nozzle to swap and no purge tower to fill. A dual-material resin printer runs two resin vats and two light engines, or one engine switching between two tanks — either way, the machine builds a layer in one resin, cleans, and builds the next layer in the other.
In practice that buys you two-tone parts straight off the plate: a red body with a white detail, a clear lens in an opaque housing, a flexible gasket bonded into a rigid shell in one print. It does not buy you a multi-colour model the way a filament AMS does, because each layer can only be one resin at a time.
For most people printing miniatures, that is a novelty. For anyone printing functional parts — a housing with a soft seal, a two-material knob — it removes a gluing step and a failure point. If you do not have that job, the £150 is buying a feature you will demonstrate once.
Photon P1 14K at £500 is the single-material version, and three separate listings agree on that price.
When three listings agree, check the shipping
Three sellers at £500 with review counts of 27, 16 and 6 stars-worth of ratings is not three identical offers. It usually means one is the brand's own listing and two are marketplace sellers holding stock, and the difference shows up in delivery time, returns handling and whether the warranty runs through Anycubic or through a third party.
For a resin printer that matters more than for a toaster. The first thing that fails on these machines is the LCD, and an LCD replacement under warranty requires the seller to accept the claim.
My rule with these clusters: buy the listing with the highest review count if the price is identical. 27 ratings is not much, but it is 27 people who got a printer and a working returns path.
The £950 question
The Photon P1 Max sits above all of this at £950, with an 18.3 litre build volume. Foto3D's write-up of the European launch lists the specifics: a 285 by 214 by 300 mm build platform, a 12K display, a heated resin vat and Wave Release film to improve separation in cold workshops.
Two things in that list are worth the money in a British garage. The heated vat matters because resin viscosity climbs fast below 20 °C — a cold vat is the single most common cause of a print that fails at layer 40 with no obvious reason. Wave Release matters because release force is what kills large flat cross-sections.
One thing is not there: auto-refill. Foto3D notes the machine lacks it, and that the resin-detection AI is sensitive enough that long prints deserve a settings check before you walk away. On an 18-litre machine running multi-day prints, no auto-refill means you are estimating resin volume by eye.
Photon P1 Max at £950 is the machine to buy if the parts are large; the P1 14K is the machine to buy if they are not.
The failure mode nobody advertises
A new P1 Max owner posted in r/AnycubicPhoton that his first two prints worked and everything after that came out as "pancakes" in the vat — the machine reporting a print in progress while nothing adhered to the plate. He was slicing in Lychee.
That is a levelling or exposure problem, not a hardware fault, and it is the standard entry fee for resin printing: the first week is calibration, and the machine's own test file proves almost nothing because it is sliced for the machine, not for your resin.
Budget for that week. It is the difference between a printer that works and a printer you sell on eBay in February.
Resin versus filament, one more time
Nobody buying a Photon P1 needs the argument. But the cost side is real and it is not in the listing price: IPA for washing, a cure station, nitrile gloves, ventilation, and resin at roughly £25 to £40 a litre depending on the formulation. A £500 printer with no wash-and-cure station is a £650 printer that produces sticky parts.
Anycubic sells the Wash & Cure units separately for exactly this reason. Factor one in before deciding that £500 is the budget.
Verdict
For miniatures, tabletop terrain and small mechanical parts, the Photon P1 14K at £500 is the right machine and the dual-colour version is not worth £150. Buy from the listing with the most reviews, add a wash-and-cure station, and accept a week of calibration.
Photon P1 14K dual colour at £650 earns its premium only if the job involves two materials in one part — a soft seal in a rigid housing, a clear window in an opaque case. That is a workshop requirement, not a hobby one.
And if the parts are bigger than a fist, skip both and go to the P1 Max. The heated vat alone justifies the step in an unheated garage between October and March.