PrintVerdict

Best 3D Printer under £600: Anycubic Kobra X against the Kobra X Combo

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

The same printer, twice the price. The Kobra X is £280 with four colours built in. The Kobra X Combo is £559 with seven colours and a box of filament sitting next to it. Between them sits a decision about how much multicolour you actually print.

What the £280 machine really is

TechRadar's Alastair Jennings tested the Kobra X and called it “a 4-color 3D printer that's surprisingly good”, with the caveat that its open design limits engineering materials. That is the important structural fact: the Kobra X is an open-frame Cartesian bed-slinger, not an enclosed chamber. PLA and PETG are its territory. ABS and ASA will warp on a draught, and no amount of calibration fixes an open frame in a cold room.

What you do get is unusual at the price. Four filaments load into a switcher built into the toolhead, which means the filament path is short — Tom's Hardware called it “a brilliant multi-material filament switcher built right into the tool head that cut down on time and filament waste”. Short paths mean less purge per colour change, and less purge is the difference between multicolour printing being fun and being an expensive hobby.

There are three catches worth knowing before you order. The frame is open, so the chamber runs at room temperature. Non-Anycubic filament requires the RFID sticker trick to register properly — TechRadar's advice was blunt: “keep the RFID sticker close if you want to use non-Anycubic filaments”. And All3DP, reviewing the same machine, concluded that the waste saving is real but smaller than Anycubic's marketing implies, and that long-term spare parts availability is unclear given how fast the company replaces its product line.

What the extra £279 buys

The Combo adds an ACE 2 Pro: a four-slot filament changer with active drying, connected by PTFE tubes. One unit turns four colours into seven on the Kobra X, two units reach eleven, four units reach nineteen. In Germany the same bundle is listed at €549 for seven colours, €698 for eleven and €1,138 for nineteen — which tells you how quickly the accessories outrun the printer's own price.

That seven-versus-four gap is smaller than it sounds. The Kobra X uses four slots in the toolhead. The Combo uses those four plus three more from the ACE 2 Pro's first channel arrangement. If you routinely print models that need five, six or seven distinct colours in one job, the Combo is the only version that does it without you standing there swapping spools. If you print in two or three colours, the extra £279 buys capacity you will not use.

The ACE 2 Pro also dries filament at 65°C, which matters in a British climate more than most reviews admit. PLA left out for a fortnight in a damp spare room prints badly, and a drying box fixes that without you buying a separate dehydrator.

The reliability question nobody wants to answer

Here is the part that should slow you down. Creative Bloq spent four months with the Kobra 3 V2 and concluded that the printer itself was fine but “the Ace Pro is problematic at best” — frequent clogs, jams and tangled filament, traced back to the multicolour unit rather than the printer. The same reviewer had previously had two faulty Kobra S1 Combos. That is the previous-generation ACE Pro, not the ACE 2 Pro in this bundle, and there is no equivalent long-term test of the 2 Pro that we can point to.

But the pattern is worth naming: the failure point in a budget multicolour setup is usually the changer, not the printer. Which is an argument for buying the £280 Kobra X first and adding the changer later if you actually need it — the printer works alone, and a clogged changer you did not buy cannot ruin your weekend.

Print quality and speed, in numbers

Both versions run the same motion system: 600 mm/s claimed maximum, 260 mm build cube, vibration compensation and automatic bed levelling, a 720p camera for timelapses, and noise under 45 dB in normal operation. TechRadar's tester had two older Kobra 2 machines still running after three years and said the print quality of the Kobra X was on a par with the Creality and Bambu Lab machines at the same price point. Tom's Hardware lists the Kobra X as its budget pick for 2026 and explicitly kept it there after reviewing the newer Kobra 4 Combo.

That last point deserves emphasis. Anycubic has since released the Kobra 4 Combo at $379, and Tom's Hardware still says the Kobra X is the one to buy because the 4 is “a bit unwieldy when compared to the clean filament paths and slender footprint of the Kobra X”. When a reviewer prefers the older, cheaper machine after testing the replacement, the older machine is usually the value pick.

Verdict

Buy the Kobra X at £280. It is the budget multicolour printer that two independent outlets rate as the class leader, it has the cleanest filament path in its price bracket, and it does not tie you to a changer that has a documented history of clogging in the previous generation. Add the ACE 2 Pro later if you find yourself genuinely needing a fifth colour.

Buy the Kobra X Combo at £559 only if you already know your models need five to seven colours in a single print, or if you want the drying function and would otherwise buy a dehydrator anyway. The £450 listing with 268 ratings is the better of the two Combo prices we track — check which one is live before you pay.

And if you need ABS, ASA or polycarbonate, buy neither. An open frame is the wrong architecture and the higher-spec Combo bundle does not change that — you need an enclosure, and that is a different purchase decision entirely.