Anycubic Kobra X 3D Printer Review: four colours for $300, and the two numbers nobody quotes
Three hundred dollars for a printer that changes filament four times without you touching it. That sentence is why the Kobra X exists, and it is also why the listing pages are confusing: the $300 model carries 4.3 stars from 92 ratings and is described as "Native 4-Color, Up 19-Color with 4 ACE 2 Pro" — which is true, and which means something very different from what a first-time buyer assumes.
Two numbers decide whether this machine is right for you. The first is $300, the price of the printer on its own. The second is $290, the price of one ACE 2 Pro filament unit. Nineteen colours requires four of those. Do that arithmetic before you get attached to the spec sheet.
What $300 actually gets you
An open-frame cartesian printer with a 260 × 260 × 260 mm build volume — 17.6 litres — and a four-filament head that hangs spools openly off the frame. CHIP's test lab measured a 20 mm calibration cube at 0.2 mm total deviation, printed a single-colour version in 36 minutes, and recorded 121 W power draw. Minimum layer height is 0.08 mm.
TechRadar's Alastair Jennings reviewed it and landed on the honest summary: the Kobra X is "a major update to the Anycubic range," with an updated touchscreen, multifilament printing and a build that feels solid, but the open design "limits the potential for utilising engineering materials." Translation: PLA, PETG and TPU are fine. ABS and ASA will warp, because there is no chamber to hold warm air around the part. If you want to print those, you are shopping for the enclosed S1 instead.
His other warning is the kind of thing that only shows up in a real review: keep the RFID sticker close if you want to use non-Anycubic filament. The machine reads spool tags, and third-party spools need that workaround. Not a dealbreaker, but it is friction you will hit on day two.
The 19-colour claim, unpacked
A single ACE 2 Pro holds four spools and dries them. The Kobra X's own head handles four colours natively; adding ACE units multiplies that. Four ACE 2 Pro boxes at $290 each gets you to the advertised 19, which puts the full multicolour setup at roughly $1,460 before you buy a single spool of filament.
There is also a middle tier that makes far more sense for most people: the Kobra X Combo with one ACE 2 Pro at $500, 4.2 stars from 314 ratings. That buys seven colours and, more importantly, active drying — which matters more to print quality than colour count does. Wet PETG prints badly on any machine.
Purge is the hidden cost of every colour change
Multi-material printing on a single-nozzle machine wastes filament by design. VoxelMatters' testing on the Kobra S1 family produced a figure worth remembering: a 10.9 g Benchy with 183 g of purge. Every swap costs roughly two minutes and a length of discarded plastic, and a four-colour model can run eight or nine times longer than the same model in one colour.
None of that is unique to Anycubic. It is what happens when one nozzle has to serve four spools. But the Kobra X's slicer does not make the trade-off obvious before you hit print, so plan your first multicolour job as a small test object, not a twelve-hour centrepiece.
Material limits, measured rather than guessed
CHIP's testers found a specific failure: soft TPU in Shore A hardness buckles before it reaches the extruder gears and jams, because the filament is cut and re-fed at every change. Anycubic's own guidance is to use harder TPU (Shore D). That is a real constraint if you bought this machine hoping to print phone cases and gaskets in one job.
Everything else on the common list works. PLA, PETG, ABS with the door open and expectations managed, and the 0.08 mm minimum layer handles fine detail work. The magnetic spring-steel plate and automatic levelling make the first layer repeatable, which is more than can be said for the $200 printers this thing is undercutting on features.
Where it sits against the competition
Jennings put it plainly: at this price the Kobra X is on par with the Creality Hi and competitive with Bambu's A1, and it does not bring anything new beyond refinement of the bed-slinger formula. Tom's Hardware's Denise Bertacchi reviewed it under the headline "Hidden AMS — another Bambu Lab clone, or something better?" — which is the correct question. The answer, from both reviews, is "better in some places, the same in most."
What Anycubic does have is the app and the ecosystem around it. Owners who moved from the Kobra S1 to a Bambu P1S have complained publicly that the Bambu app shows less — no layer number, no remote chamber temperature, no filament-used counter. Anycubic's is uglier and more capable. For a beginner who wants to watch a print from the sofa, that is worth something.
Verdict
Buy the $300 Kobra X if you want to print in four colours occasionally, in PLA and PETG, and you accept that the enclosure question is settled — it does not have one. It is the cheapest credible route into automatic filament switching, and the print quality at 0.2 mm deviation on a 20 mm cube is genuinely fine for decorative and functional parts.
Step up to the $500 Combo if you plan to print PETG seriously, because the dryer is the part you will actually use every week. Skip the 19-colour fantasy unless you have a specific product in mind that needs it — three ACE units cost more than the printer, take up a shelf, and generate a waste bin full of purge for every job.