Elegoo Centauri 2 at $279 vs the $329 Combo: is the best 3d printer for beginners worth going multicolour?
Fifty dollars. The Elegoo Centauri 2 is $279. The Centauri 2 Combo is $329. Both print the same 256 mm cube, both do full auto calibration, both sit on the same CoreXY frame. The Combo adds a filament-changing unit and the ability to print four colours.
Fifty dollars is the cheapest multicolour upgrade on the market right now. It is also, for a lot of beginners, fifty dollars spent on a feature that adds failure modes rather than value.
What the $279 machine is actually for
Elegoo built the Centauri line to do one thing well: give a first-time owner a printer that works without a weekend of tuning. Automatic bed levelling, automatic calibration, a claimed 500 mm/s ceiling that nobody reaches on a first print, and an open frame so you can see what the extruder is doing.
The open frame is the honest part of the design. It means PLA and PETG print beautifully, and ABS or ASA will warp and delaminate on a cold British or North American garage bench. If you want an enclosure, Elegoo sells the Carbon variant for more money and it is a different product, not a lid.
At $279 this is the cheapest credible entry into the current generation of fast CoreXY printers. Two years ago the same money bought a bed-slinger with half the rigidity.
What the extra $50 gets you
The Combo ships with a four-spool changer. In practice that means: four colours in one print, automatic filament switching mid-layer, and a purge tower that eats filament every time the colour changes. On a small model with eight colour changes, the waste can exceed the model.
Tom's Hardware reviewed the Centauri 2 Combo and described it as a budget-friendly printer made even more budget-friendly — the tone suggests the multicolour unit does not sabotage the base machine, which is not true of every combo on the market. That is worth knowing, because a bad changer turns a good printer into a troubleshooting hobby.
The failure mode nobody mentions in the launch video
Filament changers jam. Not always, not on every print, but often enough that the community conversation around them is dominated by clearing them. A user in r/3dprinter weighing a Centauri Carbon 2 against a Creality K2 Combo wrote that after looking at how clogs are cleared on each, the Kobra's integrated changer was "way too much hassle for me" — and noted that on the Centauri Carbon 2, clearing a bad clog means either working it out of the radiator or replacing the hotend assembly. That is a real owner describing a real task, not a reviewer's hypothetical.
So the $50 question becomes: how often will you print in more than one colour? If the answer is "for birthday presents and one Halloween model", buy the $279 machine and paint the print. If the answer is "I already have a list of multicolour projects", the Combo at $329 is the cheapest way in and you will get the money back in avoided failed single-colour workarounds.
The third option nobody asks about
Elegoo also sells the Centauri Carbon 2 Combo at $435: same family, enclosed chamber, multicolour. That is $156 more than the plain Centauri 2 and it is the version to buy if you ever intend to print ABS, ASA, or anything that needs a stable chamber temperature.
The ladder is unusually clean. $279 single colour, open. $329 four colours, open. $435 four colours, enclosed. Each step buys exactly one thing. Most manufacturers blur these lines; Elegoo has not.
On "beginner-friendly"
Every $300 printer is marketed as beginner-friendly, and nearly all of them require the same three things from a new owner: learn to level a bed (or trust the auto-leveller and check it anyway), learn what a bad first layer looks like, and learn that wet filament is the cause of half of all print defects.
The Centauri 2 removes most of the first one and none of the other two. That is genuinely progress. It is not a machine you can unbox and ignore, and no machine at this price is.
The other honest point: a $279 printer plus $40 of filament plus a $25 filament dryer is $344 — more than the Combo. Budget the accessories before you decide which printer you can afford, because wet filament in an unheated room will ruin more prints than a single extruder ever will.
Where the risk sits
Buy from a retailer with a real return window rather than the cheapest marketplace listing. Two of these machines will arrive with a bent gantry or a firmware bug, and the difference between a replacement in five days and a support ticket in three weeks is worth more than $20 of discount. Elegoo has been shipping firmware updates for the Centauri line through 2026, which is a point in its favour at this price — a printer that never gets updated is a printer that never gets its bugs fixed.
Also budget for a spare hotend. The one part you will destroy, and the one part that is out of stock whenever you need it, is the assembly you clog at 11 pm on a Sunday.
My call
First printer, PLA and PETG, wants to learn the mechanics: Centauri 2 at $279. Fewer moving parts, fewer failure modes, and $50 towards a dryer and a spare hotend.
Already has a project list that needs colour, or is buying for a household with kids who will not accept grey: Centauri 2 Combo at $329. Fifty dollars for four colours is the best ratio in the Elegoo range and probably in the whole sub-$400 market.
Wants ABS or ASA: neither of these. Spend the $435.