PrintVerdict US

The creality ender 3 v3 se at $233 against a four-colour Kobra X at $300

We have not tested either printer. Nothing here was assembled, calibrated or printed by us. Prices and rating counts come from our own US feed; specifications are Creality's and Anycubic's published figures as reported by Tom's Hardware and TechRadar. The troubleshooting list is from Creality's own wiki, and the owner complaint is a public post on r/3Dprinting, quoted as one report and not as a measured failure rate.

$67. That is the whole distance between a single-colour bed slinger that Tom's Hardware gave an Editor's Choice badge and a four-colour machine that another reviewer called a "true leap forward" for its price class.

Our US feed: Ender 3 V3 SE at $233 with 714 ratings at 4.0, or $234 with 2,600 ratings at 4.0. Kobra X at $300 with 174 ratings at 4.2, or $300 with 67 ratings at 4.0. Nearly the same money. Almost nothing else in common.

What the Ender does well, and it is not a short list

Tom's Hardware's review is unusually warm about a $199 machine. The Ender 3 V3 SE borrows auto bed levelling from Creality's K1 series and the Sprite direct-drive extruder from the S1 — the review notes the Sprite has "amazing grip" with TPU, which is the material most budget printers handle badly. Top speed is 250 mm/s, normal printing around 150 mm/s, with linear rods on the Y axis.

It is 90% pre-built. Assembly is a handful of screws, and the base has slots that hold the gantry square while you tighten it — a small design decision that removes the most common source of a crooked first print.

Then the missing feature: no Wi-Fi. Files go on an SD card. The review frames that as a plus for people who want their printer off the network, and it is — right up until the third time you walk a card across the room.

What the Kobra X does differently

Four colours, natively, with the changer in the toolhead. Tom's Hardware's Kobra 4 Combo review, written later, describes that design as the leap: a "brilliant multi-material filament switcher built right into the tool head that cut down on time and filament waste." They also declined to knock it off its "best budget 3D printer" spot when the Kobra 4 arrived.

TechRadar's review of the Kobra X adds the practical caveats: open frame, so engineering materials are out; and the RFID sticker needs to stay close if you use non-Anycubic filament, which is an odd dependency to build into a printer that costs $300.

The feed numbers are worth a second look. The Kobra X listings carry 174 and 67 ratings. The Ender carries 714 and 2,600. The Ender has been on sale far longer and has been bought by far more people — which is exactly what you would expect for a machine that costs less than a mid-range phone and does one thing well.

The decision, in three questions

Do you print TPU? Then the Ender. The Sprite direct-drive extruder is the reason. A Bowden-fed or multi-material path is the wrong tool for flexible filament, and no amount of colour changing compensates.

Do you want multicoloured models? Then the Kobra X. Painting a model or printing it in four pieces and gluing them is a hobby in itself, and most people who say they will do it, don't.

Do you print parts that must be strong? Neither. Both are open-frame machines. PLA and PETG are fine; ABS and ASA will warp. The $67 difference is irrelevant next to that constraint.

The hidden cost of the cheaper machine

An Ender 3 V3 SE at $233 is a machine with a large, well-documented failure surface: the Creality wiki has a troubleshooting page listing X-axis motion anomalies, extruder noise, first-layer adhesion problems, levelling data errors beyond ±1.2 mm, blue screens after firmware updates, and prints that stick to the plate too hard. That is not a criticism — every budget printer has a page like that — but it is a realistic picture of year one. You will learn what a first layer looks like when it is too squished.

The Kobra X has its own version of that page, and a more expensive one. A public r/3Dprinting post from an Anycubic owner describes a print head that "is not built for repair, yet it often needs repair", alongside praise for the machine's early months. Again: one owner, not a statistic. But if you are choosing between two machines at this price, the one with 2,600 ratings and three years of forum threads is the one whose problems you can look up before you hit them.

Two Ender listings, one decision

The Ender appears twice in the feed: $233 with 714 ratings, $234 with 2,600. Same printer, one dollar apart, and the cheaper listing has a third of the review history. Buy the $234 one. A dollar is not worth losing sight of the larger sample, especially when the larger sample is the one that tells you about the first-layer problems you are about to have.

The Kobra X is listed twice at $300, with 174 and 67 ratings at 4.2 and 4.0. There, the smaller sample is the less flattering one, which is usually the more informative of the two.

What I would buy

For a first printer, for a teenager, for a workshop where the machine makes brackets and jigs: the Ender 3 V3 SE at $233. It is the best-value single-colour printer in this price band, the direct drive handles flexible filament, and $233 leaves budget for filament.

For a first printer bought specifically to make colourful things — dice towers, props, models for a kid's birthday: the Kobra X at $300. The $67 buys a capability, not a specification, and that is the only kind of upgrade worth paying for at this end of the market.

And if you already own an Ender 3 of any generation: neither of these is an upgrade. Save for a CoreXY machine with an enclosure. That is the jump that changes what you can print.