PrintVerdict US

Kobra S1 Max at $700 against the $900 Combo: what $200 buys on a large 3d printer

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

Two hundred dollars is the price of colour. The Anycubic Kobra S1 Max is $700. The identical printer with an ACE multi-material unit attached is $900 — and a second Combo listing sits at $1,000, which is the same machine with a different bundle. Three listings, one printer, and a decision that has less to do with budget than with what you intend to print at 350 mm.

Here is the case against the Combo, before the case for it. On a 350 x 350 x 350 mm build plate, most prints are single-colour functional parts: brackets, jigs, enclosures, prop components, replacement knobs. Those prints waste nothing in a Combo, but they also gain nothing, and you have paid $200 for a mechanism that sits idle.

What the $700 machine is

The S1 Max is a fully enclosed CoreXY with a 350 °C hotend, a heated chamber rated to 65 °C, and a claimed 600 mm/s. Enclosure plus hotend temperature is the combination that decides whether you can print ABS, ASA, PC, PA and carbon-fibre blends — and it is the reason this machine exists at $700 instead of $400. Tom's Hardware's review of the smaller Kobra S1 praised the "fully enclosed with activated carbon filtration" design and described the machine as dependable enough to "set it and forget it" after hundreds of hours.

At $700 you get the printer, the enclosure, and a single-material path. For anyone printing structural parts, that is the complete product. The 350 mm cube is the real selling point: it is big enough for a full-face cosplay helmet in one piece, for furniture inserts, for robotics frames — the things people actually buy a large 3d printer to make.

What the extra $200 adds

The Combo at $900 adds the ACE unit: a filament storage and drying box that feeds up to four spools into the head, with 16 colours possible when you chain multiple units. Drying matters more than colour on this machine — a 350 mm ABS print that takes 14 hours will absorb moisture from the filament if you let it, and the ACE holds the spools at temperature while it prints. Tom's Hardware singled out the heated ACE spool holder as "awesome" on the smaller S1.

The $1,000 listing at $1,000 is the same Combo with different bundled filament or a variant SKU. There is no hardware difference worth paying $100 for. If both are in stock, buy the $900 one.

The slicer problem, which is the real story

This is where the Combo decision gets uncomfortable. Tom's Hardware's verdict on the Kobra S1 — the same platform, smaller bed — was blunt: "a Core XY machine with multicolor capabilities that I really want to love, but brings me to tears every time I run a four color print". The reason was not the hardware. It was the software.

Anycubic's slicer will not tell you how much filament a colour change is going to waste. On a small model that is annoying. On a 350 mm model with 400 colour changes it is a cost you cannot calculate before pressing print. The same review notes that filament purge is only adjustable mid-print, from the printer's touch screen, which means you discover the waste after the job has started and then babysit it.

Scale that up to the Max. A multi-colour print that fills a good part of a 350 mm bed can consume more filament in purge than in the model. Owners report exactly this on Anycubic's older Combo machines — a German reviewer of the Kobra 3 Combo put it plainly: yes, the printer produces a lot of waste, and the start-up sequence before a print does not seem very logical.

Who should pay the $200

Pay it if colour is the point. Signage, decorative pieces, models with separate colour regions, anything where painting would take longer than printing — that is what the ACE is for, and at $900 the S1 Max Combo is still cheaper than a Bambu X1C with an AMS.

Pay it for the dryer, even if you print single-colour. A heated, sealed spool box on a machine that prints ABS at 350 °C for 12 hours is not a luxury; it is the difference between a working part and a delaminated one. That justification holds regardless of colour.

Do not pay it if your parts are functional, single-colour, and large. You will spend $200 on a mechanism, then spend your evenings working around a slicer that hides the one number you need.

Three things to know before ordering

The chamber is heated but not actively cooled, so PLA in a closed 65 °C box is a bad idea — leave the door open for PLA, which sounds obvious and is the most common mistake on enclosed printers.

Support is the weak link across Anycubic's range. A Reddit thread on r/AnycubicKobraS1 documents a user with an X-axis homing failure whose print head was stuck hard enough that the back cover could not be removed, and whose main complaint was not the fault but the difficulty of communicating it to support. Budget for the possibility of fixing things yourself.

And the footprint. A 350 mm enclosed CoreXY is a substantial object — check the desk or bench before ordering, because this does not sit on a corner of a kitchen table the way a 220 mm bedslinger does.

The call

Single-colour functional parts at large scale: $700 S1 Max. That is the honest answer for most people who search for a large 3d printer, and the $200 saved buys a lot of filament.

Multi-colour, or ABS in a humid climate: $900 Combo. Not $1,000 — there is no difference.

And if you are buying this as a first printer, don't. Buy the Kobra X at $300 and learn on a 260 mm bed. The S1 Max is a machine for people who already know what they want to print and have run out of plate.