PrintVerdict US

Anycubic M7 MAX vs Photon P1 MAX: a large 3d printer decision in two sizes

We have not tested this printer. No QIDI Max4 has been assembled or run by us. The article uses QIDI's published specifications and launch post, plus Tom's Hardware's review of the QIDI Plus5 and its assessment of the QIDI Box. No print result here is our own.

Two Anycubic resin printers, both marketed as big, both over $700, and they solve the size problem in different directions. The M7 MAX goes wide and shallow: 298 × 164 × 300 mm, from a 13.6-inch 7K panel. The Photon P1 MAX goes wide and deep: 285.5 × 214 × 300 mm, from a 14-inch 12K panel and 18.3 litres of build volume.

We have not tested either machine. What follows is built from published specifications, from Tom's Hardware's review of the P1 MAX, from 3D Druck Life's hands-on test as summarised in r/MakerNewsEN, and from the two Anycubic listings' own review data.

The numbers that actually matter

M7 MAX: $750 on both current listings — one showing 303 ratings at 4.0 stars, the other 102 ratings at 4.4. That split is worth noticing. Same machine, same price, two product records, an 0.4-star gap. The lower-rated record has three times the reviews, so 4.0 is the more meaningful figure.

P1 MAX: $1,000, with 58 ratings at 4.2 on one listing and 18 at 4.1 on the other. Less history, similar sentiment.

So the real question is whether the extra $250 buys you anything you will notice. The answer depends entirely on what you print.

Where the P1 MAX earns its price

Resolution density. A 12K panel across 14 inches works out to 24.8 µm pixels, per the published spec. The M7 MAX's 7K panel across 13.6 inches is coarser. For miniatures, jewellery masters, and anything with fine surface detail viewed at arm's length, that difference shows up in the first print.

Vat heating. The P1 MAX has a 1,900 ml vat heatable to 35 °C, which matters more than buyers expect: resin viscosity changes with temperature, and a cold garage in January turns a 2-second exposure into a 4-second exposure and a lot of failed prints. The heated vat removes that variable.

The Wave Release film. 3D Druck Life measured peel force below 500 g, against Anycubic's claim of a 60% reduction. That is the single biggest quality-of-life improvement in modern resin printing — lower peel force means fewer supports and fewer failed tall prints.

Tom's Hardware's headline on the P1 MAX was "bigger, better, and tech-packed", which is a fair summary of what the extra $250 buys.

Where the P1 MAX annoys people

It is a physically large object that needs more space than the build volume suggests. With the lid open, 3D Druck Life measured roughly 850 mm of height and 650 mm of depth. If your printer lives on a shelf under a cupboard, that is a hard no.

The USB port is on the side, which is awkward against a wall. The build plate is flat with no drainage holes, so resin pools on it when you lift a print out. Neither is a dealbreaker; both are the kind of thing you notice every single week.

And 18.3 litres of resin printing is a lot of resin. A full-plate print on this machine can consume most of a 1 kg bottle, which reframes the $1,000 purchase price — the consumable cost of using the volume is real.

Where the M7 MAX wins

Price, obviously: $250 less, and 250 dollars is a wash-and-cure station plus three kilos of resin. The M7 MAX at $750 is the cheapest way into a genuinely large-format resin printer from a major brand.

It is also narrower in one dimension — 164 mm against 214 mm — which sounds like a disadvantage and is, until you have to fit it on a desk. A 13.6-inch panel in a 164 mm-deep body is a machine you can put beside a monitor. The P1 MAX is not.

For flat-ish work — nameplates, terrain tiles, architectural models, large single-piece props — the M7 MAX's proportions are the better fit. Wide and shallow is the right shape for most of what people actually print on a big resin machine.

The option nobody mentions

ELEGOO Saturn 4 Ultra 16K at $520, 402 ratings at 4.3 stars. A 10-inch 16K panel, flip-up lid, 30 °C tank heating, and the largest review base of the three by a wide margin.

It is smaller — 10 inches of panel is not 13.6 — but it has more owner feedback than the two Anycubics combined, and it costs $230 less than the M7 MAX. If your actual printing is miniatures and small parts, the Saturn is the rational buy and the size argument is a fantasy about projects you will never start.

What I would pick

For miniatures, small figures, and anything where 24.8 µm matters: the Photon P1 MAX at $1,000, and accept that you are paying for detail density and a heated vat, not for volume.

For terrain, props, nameplates, and one-piece large prints: the M7 MAX at $750. Its 7K panel is the weak point, and at 13.6 inches you will see layer lines on curved surfaces that the P1 MAX resolves away. You will also have $250 left for resin.

For everyone buying their first resin printer: the Saturn 4 Ultra 16K, and spend the difference on a wash-and-cure station and ventilation. Large-format resin is a second-printer purchase, not a first one — the fumes, the mess, and the resin cost all scale with the machine.

The honest caveat

All three of these are $500-plus machines with review counts in the tens or low hundreds. None of them has the accumulated owner history of, say, an Ender 3. Resin printing at this size also means ventilation, gloves, and a disposal plan for waste resin — costs that do not appear on any listing and that add up to more than the $250 gap between the M7 MAX and the P1 MAX.

Buy the size you will use. The rest is spec-sheet shopping.