PrintVerdict US

Two ways to a large 3d printer: Photon Mono M7 MAX at $750 against QIDI Max4 at $1,099

We have not tested either machine. No printer on this page has been assembled or run by us. Build volumes, chamber temperature and print speeds are the manufacturers' published figures; the rating counts are what the listings showed on the day. Nothing here is our own measurement.

$750 for 13.6 inches of resin. $1,099 for 390 by 390 by 340 mm of filament. Two large 3d printers, two processes, a $349 gap — and the gap is not really about size.

The M7 MAX is a 7K mono LCD resin machine with a 13.6-inch panel, listed twice at $750 with 303 ratings at 4.0 and 102 at 4.4. The QIDI Max4 is an FDM printer with a 65 °C heated chamber, $1,099 with 13 ratings at 4.8, or $1,299 as the Combo with 45 ratings at 4.5.

What "large" means in each process

On the resin side, large means one flat plane. The M7 MAX gives you a big footprint and modest height, which suits the things resin is actually good at: miniatures at scale, model parts, jewellery masters, dental and engineering prototypes with fine detail. A whole squad of figures on one plate, or a single model car body in one piece.

On the FDM side, large means a box. 390 × 390 × 340 mm is a helmet, a drone frame, a jig, a bracket, a tool holder. The 65 °C chamber is the important number in that list, because it is what makes ABS, ASA and polycarbonate behave — without it, large ABS parts warp off the plate before the print finishes.

Those two capabilities barely overlap. A $750 resin printer cannot make a helmet. A $1,099 FDM printer cannot make a 28 mm figure with a face.

The hidden cost of the cheaper one

Resin has consumables that filament does not: IPA, gloves, a cure station, and resin itself at $25 to $45 a litre. A 13.6-inch machine drains a vat fast — a large hollowed print can take 200 ml or more, so a litre is five prints.

Then there is the washing and curing. Anycubic sells those as separate units, and without them the parts come off the plate wet with uncured resin. The $750 printer becomes a $950 setup before the first useful print.

FDM's consumables are filament at $18 to $25 a kilo and a nozzle every few months. That is it. The Max4 at $1,099 is closer to its true cost than the M7 MAX at $750 is to its.

Photon Mono M7 MAX at $750 is the cheaper entry, not the cheaper machine.

Why the Max4 Combo exists

The $200 step from $1,099 to $1,299 buys the multi-filament unit. On a 390 mm machine that is a strange pairing at first glance — you do not usually print large multi-colour objects, because the waste tower scales with the number of colour changes and a big part has a lot of layers.

Where it earns its keep is supports and interfaces: a soluble interface layer on a large ABS part, or a two-tone enclosure where only the panel changes colour. Both are jobs where you would otherwise print in two pieces and glue.

QIDI Max4 Combo at $1,299 is worth the extra $200 if you have a specific two-material job. Not as an upgrade in the abstract.

The review counts tell you which is mature

303 ratings at 4.0 for the M7 MAX. That 4.0 is not a great score, and on a resin printer the usual causes are levelling, FEP life and screen failures — all consumable-adjacent, all fixable, all irritating.

The Max4 has 13 ratings at 4.8. Thirteen ratings on a $1,099 machine means it is new or it is niche. A 4.8 from thirteen people is a marketing number, not a reliability record. The Combo's 45 ratings at 4.5 is the first sample in this article big enough to mean anything.

That asymmetry matters. The resin machine has a track record you can read. The FDM machine does not.

What I would tell someone who asked

If the parts have faces, fine detail, or need to be smooth out of the machine — resin, and the M7 MAX at $750 is a lot of build area for the money. Accept the consumables, buy a wash-and-cure unit, and ventilate the room. Uncured resin is a sensitiser and the smell in a spare bedroom is not a joke.

If the parts are structural, bigger than a shoe box, or need to survive a drop — FDM, and the Max4's 65 °C chamber is the reason to pick it over a cheaper open-frame machine of the same volume.

What I would not do is buy the M7 MAX because it is $349 cheaper and then discover the parts need to be strong. Resin is brittle. That is not a defect, it is the material.

The $750 decision, restated

One more number worth knowing before either order: a 13.6-inch resin vat holds roughly 700 ml, and a litre of decent resin is $30 to $45. That is not a hobby budget that scales gently.

QIDI Max4 at $1,099 is the machine that makes objects you can use. The M7 MAX at $750 is the machine that makes objects you can look at closely. Both are good at their job, and neither substitutes for the other — which is why the honest answer to "which large 3d printer" is a question back: large in which dimension, and for what.

For a workshop that needs both, the $750 resin machine plus a $300 FDM printer beats one $1,099 compromise. Two processes, two price points, no pretence that one box does everything.

And if the budget only stretches to one: count the jobs. Resin wins on detail, FDM wins on size and strength, and the number of jobs each would unlock in the next six months is the only honest way to decide between them.