PrintVerdict US

QIDI Max4 at $1,099 or Combo at $1,299: a 390 mm large 3d printer and the $200 Box question

We have not tested this printer. No QIDI Max4 has been assembled or run by us. The article uses QIDI's published specifications and launch post, plus Tom's Hardware's review of the QIDI Plus5 and its assessment of the QIDI Box. No print result here is our own.

Two hundred dollars buys a QIDI Box in the Combo. The same Box costs $299 on its own. That arithmetic looks like a $99 saving, and it is exactly the kind of saving that turns into a shelf ornament.

Start with the machine, because the machine is not the controversial part. The Max4 is 390 × 390 × 340 mm — 51.7 litres of build volume — with a chamber that heats to 65 °C, a 2 mm lead Z screw with an anti-backlash nut, a bed QIDI describes as ultra-uniform across the full 390 mm, an AI camera, and active cooling-air control that the company says stops clogging. The Box is optional at both prices and included in one.

Why 65 °C matters more than 390 mm

Plenty of printers are big. Far fewer hold a chamber at 65 °C, and that single number decides which materials you can actually use rather than which ones are listed on the spool.

ABS and ASA shrink as they cool. On an open printer the bottom layer of a large part cools faster than the top, the part curls off the plate, and the layer above splits. A 65 °C chamber slows that cooling to the point where a 300 mm ABS bracket survives. Polycarbonate and nylon are the same story with a higher penalty. Without a heated chamber, a 390 mm ABS print is not a difficult print, it is a guaranteed failure.

So the Max4's real pitch is not "large". It is "large in engineering plastics". That is a narrower audience than the marketing implies, and it is the audience that should be shopping.

The Box problem, in QIDI's own review history

Tom's Hardware reviewed the QIDI Plus5 and made it an Editor's Choice, praising the heated chamber, the 370 °C nozzle and the fact that it goes toe-to-toe with a Bambu Lab H2 series for roughly half the money. Its one sustained complaint was the QIDI Box: "we only wish the QIDI Box, the multimaterial handler introduced last year, had also been improved. Right now, we're stuck with single color prints."

That is a reviewer who liked the printer and could not make the multicolour accessory work reliably. The Box is the same product family here. QIDI's own launch post for the Max4 lists "compatible with QIDI Box" as a bullet, not as a claim that colour swapping is now solved.

Which reframes the $200 question. You are not buying a $99 discount on a $299 accessory. You are buying a $200 option on a subsystem that a respected reviewer could not get to swap colours consistently on the previous generation. If it works, it is the cheapest multicolour entry in this class. If it does not, you have paid $200 for four spools of filament sitting in a box.

What the Combo actually contains

The Max4 Combo at $1,299 is the printer plus one Box. The Max4 alone at $1,099 is the printer. A second Box is $299, which means going from four colours to eight costs more than the Combo upgrade did — the usual trap in this category.

QIDI ran an early-bird window at $1,049 for the printer and $1,199 for the Combo, with a free Polar cooler thrown in. Our feed sits $50 and $100 above those numbers respectively, so if you are buying this week, check whether the early-bird pricing is still live on the brand's own store before paying the feed price. That is a $100 difference for the same box.

What a 51-litre bed changes about how you print

Three practical things, none of them obvious from a spec sheet.

First, plate adhesion stops being a detail and becomes the whole job. A 390 mm first layer that lifts at one corner will ruin a 40-hour print. You need a flat bed, a proven surface and a brim on anything with a long axis.

Second, time becomes the constraint rather than volume. At realistic speeds a 300 mm tall part is a two-day print. The AI camera is not a gimmick in that context — it is the only way you find out at hour 14 rather than hour 30.

Third, the chamber turns into a heat soak problem in summer. A 65 °C chamber in a small room is a 65 °C room. Ventilation is part of the purchase, not an afterthought.

Max4 against the Plus5 already in the line-up

The obvious comparison is QIDI's own Plus5, which Tom's Hardware made an Editor's Choice at a $749 debut price. The Plus5 is 320 x 320 x 300 mm — 30.7 litres — with a 370 C nozzle and the same heated-chamber approach. The Max4 is 51.7 litres, 68% more volume, for about $350 more.

Which one is right depends on the part, not the budget. A 320 mm cube covers most functional work: brackets, jigs, drone frames, small enclosures. The Max4 earns its premium when the part physically does not fit — a 350 mm duct, a helmet in one piece, a single-piece mould. If you cannot name that part today, the Plus5 is the better-value machine and the Max4 is a bet on future projects.

Both quote a 65 C chamber, and that number decides whether ABS is a material you can use or a material you read about. Neither is enclosed the way a workshop machine is; both hold enough heat for ASA on a 200 mm part.

The verdict I would give a friend

Buying this to print ABS and ASA parts for a workshop, one colour, functional: the $1,099 Max4 is a lot of heated-chamber printer for the money, and the Box stays on the shelf where it belongs.

Buying it because you want multicolour and you like the price: order the Combo, then spend the first week testing colour swaps on cheap PLA before you commit a 30-hour print to it. If the Box misbehaves, you have 30 days to decide whether $200 came back to you.

Buying it as a first printer: don't. A 51-litre heated-chamber machine is a tool for someone who already knows what a first layer should look like. The $1,099 is not the expensive part — the eight kilograms of filament you will burn learning on it is.