88 litres for £380: the Anycubic Kobra 3 Max V2 is the best 3d printer for beginners who ran out of bed space, not for everyone
There is a specific moment that sends people to a printer this size. You have been printing for six months on a 220 mm bed, you have a project that needs a 380 mm part, and the only options are learning to weld two halves together or buying a bigger machine. That is the customer for the Kobra 3 Max V2, and at £380 it is a remarkable amount of machine for the money.
Everyone else should read the next 900 words before ordering, because 88 litres of build volume is not free. It costs floor space, it costs heat-up time, it costs a 1,100 W power draw, and it costs the assumption that bigger is better.
The numbers that actually matter
Build volume: 420 × 420 × 500 mm. That is 88.2 litres, roughly four times a 220 mm cube. Nozzle at 300 °C, bed at 90 °C, layer heights from 0.08 to 0.28 mm, single 0.4 mm extruder, and Anycubic's own FAQ lists PLA, PETG, ABS and TPU as supported materials.
Print speed is quoted at up to 600 mm/s with 10,000 mm/s² acceleration. Anycubic's own wiki is more conservative: the recommended speed for the Kobra 3 Max is 300 mm/s, with a claimed 18-minute Benchy at tuned settings and 48 minutes at recommended ones. That gap between 600 and 300 is the normal marketing inflation in this category, but it is worth knowing before you plan a print farm around it.
Motion is CoreXY-style with dual Y-axis motors and LeviQ 3.0 automatic bed levelling. Dual Y motors and two Z screws are the reason a 420 mm bed can stay level at all — a single motor on a bed this wide is where cheap large-format printers fall apart.
The footprint is the hidden spec
The machine measures 706 × 640 × 753 mm and weighs 18 kg. With the spool holder and the bed's travel, the working footprint is closer to 706 × 940 mm. That is a metre of depth, on a desk that also has to hold a monitor.
Then there is noise. Anycubic rates it at about 60 dB when printed at recommended parameters. Sixty decibels is a normal conversation, sustained for eight hours, in the room next to your bedroom. This is not a printer you keep in a small flat and forget about.
And it draws up to 1,100 W. A 500 mm bed takes a long time to reach 90 °C and it holds that temperature for the whole print, which in a UK winter means real money on the electricity bill for a 30-hour job.
What £170 more buys: the Combo
The Combo at £550 adds the ACE multi-material unit, taking the machine from one colour to as many as eight with one ACE, and more with additional units. Two separate listings sit at £550 with 924 and 344 ratings respectively, so the price is not a one-off.
Whether that is worth £170 depends on whether you want multi-colour at all. Multi-colour on a large-format printer has a specific cost that nobody advertises: every colour change purges filament, and on a 420 mm bed with big models the purge volumes get ugly. A 200 g four-colour model can consume 150 g of waste. That is not a defect, it is how the technology works, but it turns a £20 print into a £28 print.
My view, having read through the owner complaints rather than run one: buy the £380 single-colour version, and spend the £170 on filament and a dry box. Large-format multi-colour is a niche within a niche.
ABS is the trap
Anycubic's FAQ says the machine can print ABS, then adds that ABS "needs a constant temperature environment" and is "generally not recommended to print directly". Read that sentence twice. There is no enclosure and no active chamber heater on the Kobra 3 Max V2.
Practically: PLA and PETG are fine. ABS and ASA will warp on a 420 mm part unless you build an enclosure, and an enclosure for a 706 mm wide printer is a DIY project, not an accessory. If your plan involves functional parts in ABS, this is the wrong machine.
Who this is genuinely for
Cosplay armour, prop helmets, architectural models, large planters, replacement panels for appliances. Anything where the part is bigger than 400 mm in at least one dimension. The £380 single-colour listing is here.
For that buyer, the alternative at this price is nothing. A 350 mm machine costs more, and two 220 mm prints glued together look like two prints glued together. The value proposition is real.
Who should buy something else
Anyone whose parts fit in 250 mm. The Kobra X at £260 does 260 mm cubes with native four-colour printing and a smaller footprint, and for miniature painters and small functional parts it is simply the better machine per pound. It is listed at £260 here.
Anyone in a flat with no spare room. See the footprint and the 60 dB.
Anyone who wants ABS or ASA. See above.
The honest verdict on the Combo
At £550 the Kobra 3 Max V2 Combo competes with 350 mm enclosed machines from other brands, which is a much harder fight. You are paying for volume rather than for a heated chamber or a camera or a better extruder. The £550 Combo listing is here, and it is the right buy only if multi-colour and 420 mm are both requirements, not one or the other.
If I were spending my own £380 this week, I would buy the single-colour Max V2, accept PLA and PETG, and put the saved £170 into four spools and a sealed box. That is a combination that will print more useful objects in the first month than a multi-colour unit will in three.
One caveat on the price: £380 is a promotional level, and this machine has moved between £400 and £600 several times in 2026. If you are reading this in a different week, check the listing before you decide the value case still holds.