PrintVerdict

Kobra X Combo at £399 against Kobra S1 Max Combo at £800: best 3d printer for beginners?

We have not tested these printers. No machine on this page has been assembled, calibrated or run by us. Our comparisons are built from published specifications, current retail prices and summaries of publicly available owner feedback — never from hands-on claims we cannot back up.

Anycubic has two multicolour machines inside £400 of each other, and the cheaper one is the more confusing purchase. The Kobra X Combo sits at £399. The Kobra S1 Max Combo sits at £800. Both claim multicolour printing. Both carry a 4.2 average. Only one of them is the right first printer for most people, and it is not the one with the bigger colour number.

The numbers on the box

ListingPriceRatingRatingsWhat it claims
Kobra X Combo£3994.2924native 7-colour, up to 19
Kobra X Combo (alt. listing)£4004.23447-colour, 2x faster
Kobra S1 Max Combo£8004.2924350 × 350 × 350 mm, 600 mm/s
Kobra S1 Max Combo (alt. listing)£7604.2344same machine, different seller
Kobra S1 Max (no AMS)£5504.2344enclosed CoreXY, 65 °C chamber

Two things to notice before anything else. First, the £399 and £800 machines share the same 924-rating pool, which means Amazon has merged the review sets of a £399 product and an £800 product. Any "4.2 stars" comparison between them is therefore meaningless as a quality signal.

Second, TechRadar's review of the Kobra X describes it as a 4-colour printer. Anycubic's listing says native 7 colours, expandable to 19. Both can be true — the machine has four feeds on the toolhead and the higher numbers involve chaining additional units — but a beginner reading "19 colours" and receiving a 4-colour workflow will feel misled, and that gap is where the one-star reviews come from.

What multicolour actually costs you

Every colour change purges filament. On a single-nozzle system with a filament changer, the purge volume depends on how different the two colours are: black to white is expensive, orange to red is nearly free. On a small model with eight colour changes you can burn more plastic in the purge tower than in the part.

That is the part of multicolour printing no listing mentions. A £399 machine that produces a 40 g model and 90 g of waste is not cheaper than a £800 machine that produces the same model with 30 g of waste — over a year of printing, the filament bill closes the gap. If you plan to print one multicolour figurine a month, ignore this. If you plan to sell prints, run the arithmetic before you choose.

Why the S1 Max Combo is the better beginner machine

Not because of the AMS. Because of the chamber. The S1 Max is a fully enclosed CoreXY with a heated chamber rated to 65 °C. That single feature decides which materials you can use: ABS and ASA warp without a warm enclosure, and no amount of slicer tuning fixes a drafty room in a British winter.

The 350 × 350 × 350 mm build volume is the second reason. A 180 mm cube — the typical budget printer — rules out helmets, large cosplay pieces, and most functional parts that need to be one piece rather than glued. If your interest is anything beyond figurines, volume matters more than colour count.

The Kobra S1 Max at £550 without the AMS is the quiet bargain in this table. You lose multicolour, you keep the enclosure, the volume and the 600 mm/s claimed speed. For a beginner who wants to print functional parts in PETG and ASA, that is the correct £550. Colour can be added later if Anycubic sells the changer separately — check before you assume it can.

What the reviews say, and who said it

TechRadar's tester called the Kobra X beginner-friendly and surprisingly good for the money, with the caveat that the colour system is the fiddly part rather than the motion system. Tom's Hardware titled its review "Hidden AMS", which is a fair description of a machine whose filament system is integrated rather than bolted on — good for footprint, harder to service when a feed jams.

The recurring owner complaint across both models, visible in the low-star reviews, is first-layer adhesion on the textured plate after a few dozen prints. The fix is a wash with warm water and dish soap, not a new printer. The second complaint is noise: 600 mm/s machines are not quiet, and a spare bedroom is not a workshop.

We have not tested either printer. Prices and rating counts come from the live Amazon UK listings on this site, 16 November 2026. The colour-count and chamber figures are manufacturer claims; the review judgements are TechRadar's and Tom's Hardware's.

A word about resin, since it is in the same aisle

If the reason you want a printer is miniatures, the FDM machines above are the wrong tool and colour is the wrong feature. A resin printer at a third of the price produces detail no 0.4 mm nozzle can match, and the trade is gloves, alcohol, ventilation and a curing station in the garage. Beginners who buy FDM for miniatures usually buy resin within a year.

The recommendation

Buy the Kobra X Combo at £399 if you want to print painted-looking figurines, you have a ventilated room, and you accept that multicolour means waste. It is the cheapest entry into colour FDM printing in the UK right now, and 924 ratings at 4.2 is not a bad crowd to join.

Buy the Kobra S1 Max Combo at £800 if you want one machine that prints large parts in engineering materials and can do colour when the mood takes you. For most beginners who intend to keep printing after the first month, this is the one that will not be outgrown.

And if you are honestly unsure whether the hobby will stick: the £550 S1 Max without the changer. Buy filament with the difference. Filament teaches you more about 3D printing than a colour changer does.